User manual HITACHI CDR-8130

[. . . ] - Consult the dealer or an experienced radio/TV technician for help. Caution : Changes or modifications not expressly approved by the party responsible for compliance could void the user' authority to operate the equipment. s For Germany / Für Deutschland Module dürfen nur an eine Sicherheits-Kleinspannungs-Versorgung(SELVKreise) nach EN60950/VDE 0805 angeschlossen werden. Die Trennung von Netzspannung muß durch einen Sicherheitstransformator geschehen. [. . . ] - If objects of any kind have been entered into your CD-ROM Drive - If liquid has been spilled into your CD-ROM Drive - If your CD-ROM Drive has been exposed to rain or water - If your CD-ROM Drive does not operate normally when the operating instructions are followed - If your CD-ROM Drive has been dropped or your CD-ROM Drive has been damaged - If your CD-ROM Drive exhibits a distinct change in performance PRECAUTIONS FOR USE Installation conditions Do not install your CD-ROM Drive under the following conditions. It may lead to trouble or affect performance by dust on the pick-up lens and the disc, by heat or vibration. 4 - In a place where an operation temperature reaches beyond the specified temperature 40C - High humidity locations - In a location subject to extreme changes of temperature and humidity - In a room where dust density higher than 0. 1 mg/m3 - In a room that has air conditioning with humidity control which may scatter calcium combinations and other powdered substances - In a room containing exhaust gas fumes such as exhaust gas from gasoline or diesel engines or corrosive gas such as H2S (Hydrogen sulfide) - In a location subject to vibration and jarring during drive operation - In a location subject to sudden shock and jolt during drive operation Mounting requirements Mount your CD-ROM drive tightly in horizontal or vertical position by screws. The inclination of your CD-ROM Drive should be within 5° as shown below. If you do not, - When the Disc Tray is opened, the disc may jump out and may be damaged. - It may cause damage to your CD-ROM drive. - Your CD-ROM Drive may not work with full performance. 5 5 5 5 Mounting screw The screws must be ISO (M3 x 0. 5) to mount the CD-ROM Drive tightly and avoid damaging the mechanism inside the CD-ROM Drive. (See page 11) Moving your CD-ROM Drive Remove the disc and close the Disc Tray before moving the CD-ROM Drive. If your CD-ROM Drive is moved with the disc loaded or the Disc Tray opened, both the disc and the CD-ROM Drive may be damaged. PRECAUTIONS FOR CARE Cleaning of the CD-ROM Drive, discs - Never clean your CD-ROM Drive and discs with silicon cloths or cloths soaked in water, solvents (thinner, benzine), abrasive cleaner, anti-static sprays, any record cleaner sprays, liquid cleaner or aerosol cleaner. It may damage or discolor the coating of the CD-ROM Drive or damage or deform discs. - Clean your CD-ROM Drive including the Disc Tray and discs with a clean, dry, soft cloth at least once a month. - Clean your CD-ROM drive's pick-up lens using a cleaning disc. 5 CONTROLS AND FUNCTIONS Front Panel (6) (2) Rear Panel 39 1 (3) (4) (1) (5) (7) (8) 40 (9) 2 (10) (1) LOADING/UNLOADING/BUSY Indicator Indicator blinks green only when the Disc Tray is being opened or closed, or when the CD-ROM drive is accessing data. (2) Disc Tray When the power of the CD-ROM Drive is turned off, the Disc Tray can not be opened and closed. (3) Headphone Jack (3. 5 mm) (4) Headphone Volume Control Adjust the headphone volume. (5) OPEN/CLOSE Button Press this button to open or close the Disc Tray. (6) Manual Emergency Eject Hole Only in case of emergency: If the Disc Tray does not open when the OPEN/CLOSE Button is pressed, the CD-ROM Drive's Manual Emergency Eject mechanism may be activated. This should be used only in case of emergency. See Page 9 about Manual Emergency Eject Procedure. (7) Audio Output Terminal Lch GND Rch (8) Device Configuration Jumper This Connector is used to set operation modes such as Master, Slave and CSEL 6 642 (Default setting) Device is Master Circuit Board 531 OR Device is Slave Cable Select (9) ATAPI Interface Connector ATAPI bus connection (40 pin) (10) Power Supply Connector (DC Input) For connecting the power supply cable. 4321 Circuit Board +5V +12V GND INSTALLATION WHAT YOU NEED HARDWARE - CD-ROM Drive - Interface cable - Mounting screws HARDWARE OPTION - Audio connecting cable SOFTWARE - CD-ROM device driver NOTE If you need a interface card or interface cable or CD-ROM device driver, contact your dealer. HARDWARE INSTALLATION To install this CD-ROM drive in the host computer, refer to the instruction manual of each host computer. And to install the interface card in the host computer, refer to the instruction manual of each host computer and each interface card. - Interface card - Power supply cable - Sound Card 7 Install the CD-ROM Drive following general installation procedure shown below. [. . . ] 4, 200 - 3, 200 rpm) 20 Capacity (1M=2 =1, 048, 576) 650 Mbytes (Mode 1) 742 Mbytes (Mode 2) Conditions : 333, 000 blocks (74 min. ) for recorded area Record Side Single side Sustained Data Transfer Rate 1, 200 - 2, 400 kbytes/s (Mode 1) (1k=210=1, 024) Access Time Average (1 / 3 - Stroke) 90 ms (Typical) (Note 1) Full Stroke 150 ms (Typical) (Note 2) Notes : 1) Average of 100 access operations, between 15-min 00-s 00-block and 35-min 00-s 00-block, with latency. 2) Average of 100 access operations, between 00-min 02-s 00-block and 59-min 59-s 74-block, with latency. AUDIO PERFORMANCE Number of Channels 2 Output Level Line : 0. 7 Vrms TYP. (47 kohms load) Headphone : 0. 6 Vrms TYP. [. . . ]