User manual HITACHI CM1786MAD

[. . . ] COLOUR MONITOR CM 1786M-AD 17 MVX VddSupersCan 17s User's Manual :_ READ THE INSTRUCTION INSIDE CAREFULLY. KEEP THIS USER'S MANUAL FOR FUTURE REFERENCES. _. ' _. Customers THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U. K. , PLEASE REFER TO THE NOTES ON THIS PAGE. [. . . ] This control is used to adjust the display to the preferred contrast level. Press the corresponding < + > or <- > buttons to change the overall picture contrast. 4. 2. Display Adjustment Controls The monitor contains preset display information on all of the available display modes and no user-adjustments are normally required. However, the front panel push buttons may be used for display adjustment in any of the display modes if necessary. Once set, the settings will be automatically saved and recalled each time a mode change is effected. When shipped from the factory, the front panel push buttons may be used to perform the following adjustments: 1. Used to adjust the proper horizontal display position. Used to adjust the picture width to the desired level. 6 Contrast Brightness Power-on LED Fig. Used to adjust the overall picture to the preferred height. Used to adjust the proper vertical display position. Used to return the display parameters of the current display mode to the factory default settings. The LED display blinks two times indicating that the settings have been changed to default. The Reset button will only recall the factory defaults of the display mode currently in use. The other display modes are not affected. Press and release the < Function > button to set the front panel controls to the alternate mode for picture geometry and color adjustments. Refer to Section 6. 1 for more information on the use of the c Function > button. This control eliminates the built-up of stray magnetic fields which affect the purity of screen colors, focus: and convergence. Use a small screwdriver to rotate this control clockwise or counterclockwise for picture rotation (tilt) adjustment. 7 I - H-width Reset 1 Fig. Press down on the release tab to access the display adjustment controls. 4. 3. Preset and User Modes The monitor incorporates 10 preset modes and four user modes. The preset modes are defined as follows: Display mode VGA VGA VGA SVGA 8514/A VESA VESA VESA VESA CAD I CAE Resolution 640 x 350 720 x 400 640 x 480 800 x 600 1024 x 768 640 x 480 1024 x 768 800 x 600 1024 x 768 1280 x 1024 fH, fV Polarity +, -9 + -3 - 31. 5 KHz, 70 Hz 31. 5 KHz, 70 Hz 31. 5 KHz, 60 Hz 35. 2 KHz, 56 Hz 35. 5 KHz, 87 Hz 37. 8 KHz, 72 Hz 48. 9 KHz, 60 Hz 48 KHz, 72 Hz 57 KHz, 70 Hz 64 KHz, 60 Hz 8 4. 4. Installing the Tilt and Swivel Base The monitor is designed to be mounted to the tilt and swivel base with which it was shipped. [. . . ] Dimension (W x H x L) / Weight l l 410 x 400 x 445 mm 20. 6 Kgs with tilt and swivel base 7. 9. Signal Connector Pin 1 Pin 2 Pin 3 Pin4 Pin 5 Pin 6 Pin 7 Pin 8 : : : : : : : : Red Green Blue Ground Ground Red - ground Green - ground Blue - ground Pin 9 : No connection Pin 10 : Ground Pin 11 : Ground Pin 12 : No connection Pin 13 : H-sync Pin 14 : V-sync Pin 15 : No connection 7. 10. Power Management This monitor is fully-compliant with VESA DPMS and the EPA for Energy Star. To take advantage of both display power management as well as meeting Energy Star guidelines, the monitor must be used with DPMScompliant display cards. 17 ::::::::::::::: ::::::::::::::i ~ Section * Power Management Utility The power management utility diskette contains the files OFFH. COM and OFFH. SCR which allows the user to set the idle time required before the monitor goes into the power saving mode. [. . . ]