User manual HITACHI CM2096ME

[. . . ] HITACHI COLOR MONITOR CM2096ME USER MANUAL For future references, record the serial number of your display monitor. The serial number is located on the rear of the monitor. EPA POLLUTION PREVENTER READ THE INSTRUCTION INSIDE CAREFULLY. KEEP THIS USER'S MANUAL FOR FUTURE REFERENCES. USER MANUAL 2 MANUAL DE USUARIO GEBRUiKSAANWiJZlNG MODE D'EMPLOI 51 66 I LI Energy Star is a trademark of Environmental Protection Agency. [. . . ] 0 8 kHz 56. 48 kHz 60. 02 kHz 6 1 APPLE 1152 X 870 - 75Hz 1 100. 00 MHz 7 CAD 1280 X 1024 - 74Hz 135. 00 MHz Note: 1. 2. 68. 68 kHz 78. 86 kHz Input signals with approximately the same frequencies may be regarded as the same signal. The following horizontal timing conditions are recommended. Horizontal front porch should be more than 0. 1 ps. Horizontal back porch should be more than 1. 2~~. Horizontal blanking width should be more than 3. 5~~. The following vertical timing conditions are recommended. Vertical blanking width should be more than 45Ops. Vertical back porch should be more than 400~s. 3. 9 ~m - See the "Control Panel" at front of the monitor. You can adjust the picture position, size, side pincushion, trapezoid, rotation, color balance, brightness and contrast of the monitor with these buttons. q If two or more buttons are pressed at the same time, they will be invalid except when mentioned in the following. 1. FUNCTION OF CONTROLS ( Power Switch [ a] 1 l Power is switched ON or OFF by pushing this button. When the power is ON, ) The power LED will lights. ) The picture position, size, side pincushion, trapezoid, color balance, brightness, rotation, and contrast of the monitor will be adjusted automatically. (refer to "Automatic Settings") ) The contrast adjustment mode will be set, and the contrast LED will light. q If all LEDs light continuously or the power LED blinks, make sure the power switch of the computer, signal cable connection, and the input sync. The monitor will recover rapidly when the monitor receives a right sync. ] 1 0 Indicates the color balance selection No. ) When the color button is pressed, the color LED will indicate the color balance selection No. Flashing once indicates the standard color balance No. Flashing Flashing three times indicates twrce indicates the standard color balance No. can be changed by pressing the [ +] / [ - ] button. Refer to "Color Balance Selection" section for detail. l Selects a colo'r to be adjusted. (with [(ID]/[e]/[ a] Button) ) Refer to "Color Adjustment" section. Geometry Adjust Button , `I [ csP]/[ 8 I/[ 81/i cOl/[ I3 I I 0:. 0. ~00 IOII ti& I I I DEGALl# I @ I I @ To adjust geometry (horizontal position, horizontal size, vertical position, vertical size, side pincushion and trapezoid). ) When a geometry adjust button is pressed, the LED of the button pressed will light. Pressing the [ +] I [ - ] button in this mode will make the appropriate adjustment. [. . . ] Pressing the [+I button will change the color balance from No. 1 to No. 2, and from No. 2 to No. 3 (if available) only. 1 Standard Color Balance 1 (LED flashes once. ) + pressing the [+I button. El + (LED flashes twice. ) + pressing the [ +] button. 9300 K) pressing the [ -1 button. q 4 2 Standard Color Balance 2 (temp. : approx. 6500 K) pressing the [ -1 button. q 4 3 User Color Balance (if available) (LED flashes three times. ) q About 10 seconds after finishing adjustment, the setting of color balance selection will be stored with the settings of contrast and brightness, and the contrast mode will be selected automatically as a default. 15 - - Color Adjustment Your own color balance can be set by adjusting each color components of red, green and blue. [. . . ]