User manual HITACHI CM751ET

[. . . ] COLOUR MONITOR CM751 ET CM752ET CM753ET with USER MANUAL. . . . . I BEDIENUNGSANLEITUNG. . . 59 EasyMenu ! EasyMenu is HITACHI's On Screen Display function for easy operation. READ THE INSTRUCTIONS INSIDE CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your colour monitor. SERIAL No. The serial number is located on the rear of the monitor. This monitor is ENERGY STAR@ compliant when used with a computer equipped with VESA DPMS. [. . . ] The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED. Install the monitor in the following way, taking care to maintain safety. Installation Install the monitor on a horizontal base. Front Cover CRT Surface Connector Power Switch Control Panel Tilt & Swivel Base FRONT VIEW , j! REAR VIEW / Signal Input Connector Signal Cable / to the host computer 2. Power Cord Connection @ Make sure of using the power cord meeting the safety standard of the country in which you are using the monitor. @ Insert the connector of a power cord to the AC Inlet of the monitor. @I Insert the plug of the power cord to a receptacle of the correct voltage. Signal Cable Connection (iJ Insert the connector of a signal cable to the Signal Input Connector of the monitor, with attention to the suitability, and secure the screws on the connector shell firmly. @ Connect the another connector of the signal cable to the host computer. AC Inlet A receptacle of the correct voltage \ `4 Power COI rd \ 6 l Use a signal cable with the D-Sub Mini 15pin Connector. 3 l If the graphics board supplies more than one type of sync. signal type will be automatically selected by the monitor, with the priority shown in the following table. 4. Power On Turn on the Power Switch of the monitor first, then the computer. Paae 9 "POWER ON/OFF" Refer to NOTICE : n After turning OFF the switch, wait at least 5 seconds to restart the monitor. Otherwise the monitor may operate unusually. n If the picture doesn't appear, turn OFF the power switch, make sure of the following and wait at least 30 seconds to restart the monitor. Make sure the power switch of the computer, power cord connection, signal cable connection and the input sync. W If the colour is impure on the screen after turning ON the monitor, wait for about 10 minutes and press the DEGAUSS button. Microprocessor-based preset functions can store 26 sets of geometry settings including the standard settings. The following industrial standard settings have been preprogrammed by the factory. No. Video Mode Name (with Resolution and Vertical Frequency) VGA 640 X 480 - 6 0 Hz VESA 800 X 600 - 85 Hz VESA1024 X 768 - 85 Hz VESA1280 X 1024 - 85 Hz VESA1600 X 1200 - 75 Hz VESA1600 X 1200 - 85 Hz Horizontal Frequency 31. 47 kHz 53. 67 kHz 68. 68 kHz 91. 15 kHz 93. 75 kHz 106. 25 kHz Video Model ;;;;;E; / CM753ET ( 1 2 3 4 5 6 VGA VESA VESA VESA VESA VESA b L L I5 I5 - & L b lb . b NOTE : W Input signals with approximately the same frequencies may be regarded as the same signal. n The following horizontal timing conditions are recommended (at sync. for 31 kHz - 52 kHz horizontal frequency: Horizontal front porch should be more than 0. 1 us. Horizontal back porch should be more than 1. 2 ys. Horizontal blanking width should be more than 3. 5 us. for 52 kHz - 107 kHz horizontal frequency: Horizontal front porch should be more than 0. 1 ps. Horizontal back porch should be more than 1 . I us. [. . . ] n It is normally not necessary to store them manually. No operation of about 8 seconds stores the currently adjusting data of these items, automatically. RESET 0 Only when you want to cancel all your storing data, turn ON the power switch (Q) while pressing the switches & together, to reset to the original standard settings. All your storing data will be lost and the all adjustment condition will be returned to the original settings. SIGNAL CHECK 0 To refer to the input signal condition, press the switch of the @?I (CONTRAST/BRIGHTNESS). The horizontal frequency and vertical frequency will be indicated. n Precision frequency, Horizontal approximately Vertical approximately zk 2 kHz 2 2Hz - CB CONTRAST 4 I ) + j G BRIGHTNESS -4-I)+ 80kHr/ i. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]