User manual HITACHI CM772U

[. . . ] HITACHI FLAT FACE COLOUR MONITOR (DJ72) CM771ET/U CM772ET/U with EasyMenu ! USER MANUAL MANUEL D'UTILISATION BEDIENUNGSANLEITUNG MANUAL DE USUARIO MANUALE DI ISTRUZIONI EasyMenu is HITACHI's On Screen Display function for easy operation. READ THE INSTRUCTIONS INSIDE CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your colour monitor. SERIAL No. The serial number is located on the rear of the monitor. This monitor is ENERGY STAR@ compliant when used with a computer equipped with VESA DPMS. The ENERGY STAR@ emblem does not represent EPA endorsement of any product or service. [. . . ] i * After turning OFF the power switch, wait at least 5 seconds before restarting the monitor. If this 5 second delay is not observed, the monitor may operate incorrectly. / Brightness/Contrast Adjustment (1) Press one of the adjustment buttons when the OSD (On Screen Display) is not shown. The OSD function "EasyMenu" then shows the condition of brightness and contrast. (2) To adjust, use the adjustment buttons @I/@ for brightness, and O/O for contrast. " I, -<< Brightness/C -. . -. ---. . . -. . -. Other Functions (1) Press the menu button when the OSD is not shown. The OSD function "EasyMenu" then shows the main menu. . The EasyMenu has 4 sub menus (Screen Menu, Recall Menu, OSD Menu and Color Menu). You can call them by the functions of the main menu. (2) To select the function of the menu, use the adjustment buttons @I/@. (3) To execute the selected function, use the adjustment buttons O/O in the Table l-l overleaf. earl: : :* Main Menu ><{ . : i NOTE: i * You can select the OSD language. Use the function "LANGUAGE SELECT" of the i "OSD MENU". i * To return to the main menu from any sub menu, press the menu button. j * To'clear the OSD, press the menu button at the main menu, use the function "OSD / EXIT", or wait for a definite period. i * The adjusted condition will be stored automatically at clearing the OSD. i * The OSD might be turned on and off continuously in a short period when the OSD is 1 displayed in a certain position of the screen. i Simply change the OSD position a little up or down, so that the OSD will be stable. l - 9 . OPERATION (Continued) Table 1-l. Adjustments * OSDEXIT * DEGAUSS =$ DMS * * = * * * COLOR MENU?BALANCE * PARALLELOGRAM PINCUSHION * TRAPEZOID V. * TRAPEZOID * P I N C U S H I O N PARALLELOGRAM + PIN. DMS * DEGAUSS =a OSD EXIT ( T o b e continued on the next page. ) I-10 OPERATION (Continued) Table 1-I. Adjustment (Continued) 1Adiustment 1 Item Function (no a RECALL MENU ? function) I 2% COLOR MENU ? [. . . ] i * In case the front or back porch is extremely long, or the data display time is ; extremely short, it may not be able to set the expected size and position. I-18 SPECIFlCATlONS (Continued) Pin Assignment Signal itqriut Connector of the Monitor [-q&-] . TCO'99 STA TEMENT Congratulations! You have just purchased product developed the environment Th[s product envwonmental joint effort Naturskyddsforen Swedish National a TC099 approved use. Your choice has provided to reduc]ng adapted provides electronics you with a on products. for professional has also contributed the burden and also to the further development for the TCO'99 Confederation Society of environmentally scheme which meets the requirements and quahty by the TCO (The Swedish Swedish for an international as a (The Svenska labell Irrg of personal computers. The Iabe[ling scheme was developed Statens Energimyndighet of Professorial Conservation), AB Employees), lngen (The Energy cover for Nature Administration) a wide and SEMKO The requirements electric range of issues' environment, consumption and electrical ergonomics, safety usability, reduction of and magnetic fields, energy Why do we have environmentally 1n many countries. [. . . ]