User manual HITACHI CMP402HDU

[. . . ] SAFETY GUIDELINES ENGLISH i This monitor is designed to be safe to use. However, due to high voltage of about 400 V, fire or serious injury may occur unless you use this monitor in correct way. You are strongly suggested to follow the instruction shown below in order to avoid such injury. Keep the safety guideline Do not use the monitor if it fails If you find something unusual , If smoke comes out, If there is a strange smell, If water enters the case, If you drop the monitor or damage the cabinet, Turn off the monitor Disconnect the power plug from the power point Request for repair Warning and Caution are indicated in this guide and monitor itself. Warning Caution Fire or electric shock may cause death or serious injury unless you follow the instruction. Electric shock or other accidents may cause serious injury or damage of your properties. SAFETY GUIDELINES(continued) Warning ENGLISH ii Fire or electric shock may cause death or serious injury unless you follow the instruction below. [. . . ] 5) Insert one end of the power cable included into the rear-panel power cable connector and the other end into a power socket. 6) Turn on the monitor, then the video equipment's to make sure that a display image appears on the monitor screen. For instructions on turning on the monitor and adjusting its display images, see "Operating Instructions" ( 9 to 16 ). Monitor rear panel Video equipment (such as a video disc player, a DVD player, and a video camer) Power cable Power cable connector AUDIO IN SPEAKER TERMINAL (88W) VIDEO2 L/MONO R + + VIDEO1 COMPOSITE IN Nearer Terminal White (W) Further terminal Red (R) COMPONENT IN PR/CR PB/CB Y VIDEO S R L Yellow (V) Use if the video equipment has an S video input terminal To component input terminals If video equipment with an S video input terminal is used, cabling by the S video cable is recommended to provide finer video quality. (If an S video input terminal and a video input terminal connect to the monitor at the same time, S video input would govern. ) 7 ENGLISH Connecting to Video Equipment To S video output terminals To component output terminals To audio/video output terminals To audio output terminals Yellow(V) Red(R) White(W) White(W) Red(R) W e hit ) (W To S video input terminals d Re (R) To audio input To audio/ video input terminals terminals INSTALLATION INSTRUCTIONS (continued) Handling the Remote Controller Loading Batteries 1) Open the battery cover. Slide the battery cover towards the arrow mark while pressing it. ENGLISH 8 2) Load batteries. Load two Size AA batteries included observing the correct polarities. 3) Close the battery cover. Slide back the battery cover towards the arrow mark. Handling the Remote Controller Use the remote controller within about 5 m from front of the unit's remote-control sensor and within 30 degrees on both sides. With in 30 degrees With in 30 degrees About 5m SELECT CAUTIONS Do not use new and old batteries together. The batteries could explode or leak, resulting in fires, physical injury, or stains. When loading batteries, observe their correct polarities as marked on the product. If loaded in the wrong direction, the batteries could explode or leak, resulting in fires, physical injury, or stains. Do not drop or impact the remote controller. Do not splash the remote controller with water or put it on a wet object to avoid possible failures. Before leaving the remote controller out of use for an extended period of time, remove the batteries from it. If the remote controller begins to lack responsiveness, replace the batteries. Strong light such as direct sunlight impinging on the photoreceptor of the remote control can cause operational failure. Position this unit to avoid direct contact with such light. TIPS OPERATING INSTRUCTIONS Turning Power On and Off ENGLISH 9 To turn on the set power supply, set the MAIN POWER switch ( ) of the main unit to ON and then press the SUB POWER button or the POWER button of the remote control. To turn off the set power supply, press the SUB POWER button of the main unit or the POWER button of the remote control, then set the MAIN POWER switch ( ) to OFF. For normal operations, leave the main power switch ( ) set to ON and use the sub power switch or the Power button of the remote control to turn the power on and off. Display lamp Off Power status Off Operating When the main power switch to OFF. is set Lights red Off (standby) * When the main power switch is set to ON and Power button of the remote control or the sub power button on the control panel located at the front part of the bottom plate is off. When the main power switch is set to ON and Power button of the remote control or the sub power button on the control panel located at the front part of the bottom plate is on. Lights or blinks green On When the indicating lamp blinks in green or the message "POWER SAVE" or "OUT OF FREQUENCY" appears on the screen, there is something unusual about the status of reception. See "Symptoms That Seemingly Appear to be Failures. " 21 *The "standby" mentioned here is different from the "standby" in Power Saving System 20 . SUB-POWER Main power switch POWER Set unit Remote controller TIPS Avoid repeatedly turning the monitor on and off at short time intervals. Failures might result from such operation. Turn off the main power switch ( ) before leaving the monitor out of use for an extended period of time. If a power failure occurs while the set is running, it would be powered on upon recovery from the failure. Turn off the unit main power switch before leaving the set. OPERATING INSTRUCTIONS (continued) Input Selection Press the RGB/VIDEO button on the remote controller or the unit to switch the input in the sequence of RGB1 -> RGB2 -> VIDEO1 -> VIDEO2 -> RGB1. When the same signal is input to RGB1 and RGB2, the phase may in some cases shift slightly but this is not a malfunction. In such case, readjust the PHASE of the one being used. Remote controller RGB/ VIDEO ENGLISH 10 RGB1 RGB2 (D-sub input) (BNC input) Set unit RGB/VIDEO VIDEO1 (composite or S input) VIDEO2 (COMPONENT input) Volume Adjustment While the on-screen display system, EasyMenu ( 12 ) is not on display, press the remote controller VOLUME button or (or the unit VOLUME button or to adjust the sound volume. The adjustment status will be displayed as guidance while you press these buttons. [. . . ] The display image appears flowing (display 2) (RGB input). Display 1 Vertical streaks Before adjustment Some characters are blurred. ABCDEFGHIJ abcdefgABCDEFGabcd ABCDEFGHIJ abcdefgABCDEFGabcd B ABC Example ABC After adjustment All characters appear crisp now. ABC ABC After adjustment All characters are blurred. Adjust 24 . Adjustment procedure 1) Press MENU button to open the adjustment menu. 2) Press SELECT button several times to choose DISPLAY. [. . . ]