User manual HITACHI CMPAK06

[. . . ] This plasma display wall-mount unit is for use only with the following model: CMP5000WX Special techniques are necessary for installation of the plasma display. Do not attempt to perform this work by yourself. Request an installation specialist to install this unit. [. . . ] Disassembly prohibited Safety Cautions WARNING When a malfunction occurs, disconnect the power plug from the power outlet and take measures to prevent other people coming near the plasma display. In the cases such as The plasma display is loose and vibrates to an extreme degree, Mounting screws or parts are loose or missing, failure to take appropriate actions can result in injury. Perform the following actions immediately whenever a malfunction occurs. Turn off the plasma display power switch. Disconnect the power plug from the power outlet. Surround the area with rope, etc. , to prevent other people coming near. Contact your local dealer. Disconnect the power plug from the power outlet. Contact your local dealer. Handling by other than professional contractors is prohibited. Ask your dealer to install, move or adjust the wallmount unit. Incorrect installation or adjustment can cause the plasma display to fall. Installation Location WARNING Plaster board or thin ply wood, etc. The wall where the wall-mount unit is to be installed must be capable of long-term support of the total load of the plasma display and wall-mount unit. Measures should also be taken to ensure sufficient strength to withstand the force of earthquakes, vibration and other external forces. Incorrect installation can cause the plasma display to fall and cause injury. Pillar or thick ply wood. Model 50 Total load of the (plasma display + wall-mount unit) = 52. 7kg Installation on a wooden wall Always install so that the load is supported by a piller. If the strength of the piller is insufficient, add reinforcement. Do not install on plasters or decorative posts. Installation on a concrete wall Use commercially available anchors that are capable of fully supporting the load of the plasma display. CAUTION Avoid installing in locations where the temperature and humidity are excessively high, and where contact with water is possible. These can result in fire or electrical shock. 10cm or more 10cm or more 10cm or more Do not block the ventilation holes. Also provide sufficient clearance in regard to the surroundings to avoid blocking the ventilation. The internal temperature could elevate and possibly result in fire. Do not install close to an airconditioner intake or outlet. Do not install in locations where there is excessive amounts of dust, oily smoke or tobacco smoke. Fire could result. Mount only on a vertical, rigid wall surface. The internal temperature could elevate and possibly result in fire. Injury or damage could also result from falling. CAUTION Do not install in locations where there is excessive vibration or impact. Injury and damage could result from falling. Do not install where there is direct sunlight and other strong light. Strong light could result in eye fatigue during usage. Installing WARNING Use the specified bolts and screws in the specified places and tighten firmly. Failure to do this could cause injury if the plasma display falls. Make sure the display fittings and wall-mount fittings are firmly engaged. Failure to do so could cause the plasma display to fall. Do not alter any of the parts. And do not use broken parts. This could result in injury due to the plasma display falling. Always use at least two people to perform the installation work. Injury could result from dropping heavy objects. Use care to prevent the fingers being caught. Installation Method Installation procedure 1 Remove the special screws (2 locations) from the bottom of the hung on wall unit. Be sure to install the speaker at this stage. For the installation method, refer to the speaker installation procedure in the speaker user manual. 5 Attach the wall side hardware to the wall. Install the wall side hardware (4 locations) symmetrically on the left and right side (one at each location from the center of the ). [. . . ] When this happens, adjust it at the center of the upper. Turn the screws very carefully to avoid damaging the wall. When a screw becomes tight at either end of the adjustment range, do not turn the adjustment screw any further, because if you do, you will apply excessive force, deforming the screw. (A) Criterion for the vertical location Gap disappears Back of the plasma display (B) Criterion when its angle is 25 End face of the plate Resin plate Wall side hardware Notch Matched in both directions When it is in this state, do not turn the adjustment screw any further in the closing direction. When it is in this state, do not turn the adjustment screw any further in the opening direction. Opening Closing Hexagon wrench Measuring the opening distance X enables approximate angle values to be determined. [. . . ]