User manual HITACHI CP-L540E

[. . . ] · The manufacturer assumes no responsibility for any errors that may appear in this manual. · The reproduction, transmission or use of this document or contents is not permitted without express written authority. Contents of package NOTE · Keep the original packing materials for future reshipment. For moving the projector, be sure to use the original packing material. (1) Projector with Lens cover (2) Strap (for Lens cover) (3) Filter cover (for bottom-up use) (4) Remote control (5) Two AA batteries (for Remote control) (6) Power cord (7) RGB cable (8) User's manuals (3) (4) (1) VIDEO RGB SEARCH ASPECT AUTO BLANK MAGNIFY ON VOLUME OFF MUTE (2) FREEZE KEYSTONE POSITION ZOOM + MENU ENTER ESC RESET (5) (6) (7) (8) 1 Preparations Preparations Fastening the lens cover WARNING Do not fasten the lens cover during use or immediately after use. [. . . ] Do not look into the lens or vents of the projector. ENGLISH NOTE · Turn the power on in right order. Please power on the projector before the connected devices. SEARCH button RGB button VIDEO button ASPECT button LAMP TEMP VIDEO RGB SEARCH POWER ASPECT AUTO BLANK MAGNIFY ON VOLUME INPUT POWER indicator INPUT button Focus ring Power switch OFF MUTE FREEZE KEYSTONE POSITION ZOOM + MENU STANDBY/ON button MENU ENTER ESC RESET ZOOM buttons STANDBY/ON and set the power switch to the ON position. Open the lens cover, will light to solid orange. Then wait several seconds The power indicator because buttons may not function for these several seconds. POWER (Solid orange) on or remote control. Press the STANDBY/ON buttonand the projector indicator will begin blinking The projector lamp will light up the POWER green. When the power is completely on, the indicator will stop blinking and light green. POWER (Blinking green) POWER (Solid green) Displaying select an input the button of INPUT 1. To RGB, VIDEO orsignal, use(remote control). (projector), or the buttons of SEARCH 2. To change the aspect ratio, use the button ASPECT (remote control). To adjust the zoom and focus, use the ZOOM buttons (remote control) and the focus ring (projector). 7 Operating Controls LAMP indicator TEMP indicator POWER indicator INPUT LAMP TEMP POWER INPUT button Cursor buttons , , , MENU STANDBY/ON button STANDBY/ON Remote control SEARCH button RGB button VIDEO button ASPECT button VIDEO RGB SEARCH STANDBY/ON button AUTO button BLANK button BLANK ASPECT AUTO MAGNIFY ON VOLUME VOLUME button MUTE button KEYSTONE button Zoom + button - button MENU button MAGNIFY ON button OFF button FREEZE button OFF MUTE FREEZE KEYSTONE POSITION ZOOM + MENU POSITION button ESC ENTER RESET ESC button Menu cursor buttons , , , ENTER button RESET button 8 Operating Turning off the power NOTE · Turn the power off in right order. Please power off the projector after the connected devices. Note that shards of glass could damage the projector's internals, or cause injury during handling, Disconnect so please do not try to clean the projector or replace the lamp yourself. the plug · If the lamp should break (it will make a loud bang when it does), from the ventilate the room well, and make sure not to breathe the gas that power comes out of the projector vents, or get it in your eyes or mouth. outlet · Before replacing the lamp, turn the projector off and unplug the power cord, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp. · Never unscrew except the appointed (marked by an arrow) screws. · Do not open the lamp cover while the projector is suspended from above. This is dangerous, since if the lamp's bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken. · Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury. [. . . ] (4) Choose the "RESET" using the button . NOTE · Incorrectly resetting of the filter timer (resetting without replacement, or neglect of resetting after replacement) will result in incorrect message functions. 12 About "User's Manual ­ Operating Guide" The "User's Manual - Operating Guide" of this projector is written into the CD-ROM. Before using, please read the following and use the CD-ROM correctly. CAUTION · Only use the CD-ROM in a computer CD drive. NEVER INSERT THE CD-ROM INTO A NON-COMPUTER CD PLAYER! [. . . ]