User manual HITACHI CP-S860E

[. . . ] · Although the projector can display signals with resolution up to UXGA (1600x1200), the signal will be converted to the projector's panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and projector panel are identical. · Automatically adjustment may not function correctly with some input signals. [. . . ] The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Data H. Sync (A) Computer/ Horizontal signal timing (s) Signal (A) (B) (C) (D) TEXT 2. 0 3. 0 20. 3 1. 0 VGA (60Hz) 3. 8 1. 9 25. 4 0. 6 VGA (72Hz) 1. 3 4. 1 20. 3 0. 8 VGA (75Hz) 2. 0 3. 8 20. 3 0. 5 VGA (85Hz) 1. 6 2. 2 17. 8 1. 6 SVGA (56Hz) 2. 0 3. 6 22. 2 0. 7 SVGA (60Hz) 3. 2 2. 2 20. 0 1. 0 SVGA (72Hz) 2. 4 1. 3 16. 0 1. 1 SVGA (75Hz) 1. 6 3. 2 16. 2 0. 3 2. 7 14. 2 0. 6 SVGA (85Hz) 1. 1 Mac 16" mode 1. 1 3. 9 14. 5 0. 6 XGA (60Hz) 2. 1 2. 5 15. 8 0. 4 XGA (70Hz) 1. 8 1. 9 13. 7 0. 3 XGA (75Hz) 1. 2 2. 2 13. 0 0. 2 XGA (85Hz) 1. 0 2. 2 10. 8 0. 5 1152 x 864 1. 2 2. 4 10. 7 0. 6 (75Hz) 1280 x 960 1. 0 2. 9 11. 9 0. 9 (60Hz) 1280 x 1024 1. 0 2. 3 11. 9 0. 4 (60Hz) 1280 x 1024 1. 1 1. 8 9. 5 0. 1 (75Hz) 1280 x 1024 1. 0 1. 4 8. 1 0. 4 (85Hz) 1600 x 1200 1. 2 1. 9 9. 9 0. 4 (60Hz) Front porch (D) Back porch (b) Data V. Sync (a) Computer/ Vertical signal timing (lines) Signal (a) (b) (c) (d) TEXT 3 42 400 1 VGA (60Hz) 2 33 480 10 VGA (72Hz) 3 28 480 9 VGA (75Hz) 3 16 480 1 VGA (85Hz) 3 25 480 1 SVGA (56Hz) 2 22 600 1 SVGA (60Hz) 4 23 600 1 SVGA (72Hz) 6 23 600 37 SVGA (75Hz) 3 21 600 1 SVGA (85Hz) 3 27 600 1 Mac 16" mode 3 39 624 1 XGA (60Hz) 6 29 768 3 XGA (70Hz) 6 29 768 3 XGA (75Hz) 3 28 768 1 XGA (85Hz) 3 36 768 1 1152 x 864 3 32 864 1 (75Hz) 1280 x 960 3 36 960 1 (60Hz) 1280 x 1024 3 38 1024 1 (60Hz) 1280 x 1024 3 38 1024 1 (75Hz) 1280 x 1024 3 44 1024 1 (85Hz) 1600 x 1200 3 46 1200 1 (60Hz) Front porch (d) Display interval (C) Display interval (c) 2 Connection to the ports Connection to the ports A Y AUDIO IN2 R CONTROL CB/PB CR/PR VIDEO S-VIDEO L AUDIO OUT AUDIO IN1 RGB IN1 RGB IN2 RGB OUT K B USB RGB IN OUT switch When this switch is not pushed in, RGB IN2 is selected. When this switch is pushed in, RGB OUT is selected. A RGB IN1, B RGB IN2, RGB OUT D-sub 15pin mini shrink jack · Video signal: RGB separate, Analog, 0. 7Vp-p, 75 terminated (positive) · H/V. Signal: TTL level (positive/negative) · Composite sync. Signal: TTL level 5 10 4 9 3 8 2 7 1 6 15 14 13 12 11 At RGB signal Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Signal Video Red Video Green Video Blue (No connection) Ground Ground Red Ground Green Ground Blue (No connection) Ground (No connection) A : SDA (DDC data), B H. A : SCL (DDC clock), B Pin 1 2 3 4 5 6 7 8 9 10 11 15 At component video signal CR/PR Y CB/PB (No connection) Ground CR/PR Ground Y Ground CB/PB Ground (No connection) Ground Signal (No connection) * B Except when set to RGB OUT 3 Connection to the ports C Y AUDIO IN2 R CONTROL RGB IN1 RGB IN2 RGB OUT K D CB/PB E CR/PR VIDEO L AUDIO OUT USB G AUDIO IN1 S-VIDEO F COMPONENT VIDEO C Y, D CB/PB, E CR/PR RCA jack x3 · System: 525i(480i), 525p(480p), 625i(576i), 750p(720p), 1125i(1080i) Port Signal Y Component video Y, 1. 0±0. 1Vp-p, 75 terminator with composite CB/PB Component video CB/PB, 0. 7±0. 1Vp-p, 75 terminator CR/PR Component video CR/PR, 0. 7±0. 1Vp-p, 75 terminator F S-VIDEO Mini DIN 4pin jack Pin 1 2 3 4 1 3 2 4 Signal Color signal 0. 286Vp-p (NTSC, burst), 75 terminator Color signal 0. 300Vp-p (PAL/SECAM, burst) 75 terminator Brightness signal, 1. 0Vp-p, 75 terminator Ground Ground G VIDEO RCA jack · System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4. 43, PAL60 · 1. 0±0. 1Vp-p, 75 terminator 4 Connection to the ports K CONTROL Y I AUDIO IN2 R M RGB IN1 L RGB IN2 RGB OUT K CB/PB CR/PR J L AUDIO OUT AUDIO IN1 H USB VIDEO S-VIDEO H AUDIO 1-IN (Ø3. 5 stereo mini jack), I J AUDIO 2 L/R (RCA jack) · 200mVrms(max. ) 35k termination K AUDIO OUT (Ø3. 5 stereo mini jack) · 200mVrms(max. ) 1k output impedance L USB USB B type jack 1 2 4 3 Pin 1 2 3 4 +5V - Data + Data Ground Signal M CONTROL D-sub 9pin plug 5 9 4 8 3 7 2 6 1 · About the details of RS-232C communication, please refer to the following page. Pin Signal 1 (No connection) 2 RD 3 TD Pin Signal 4 (No connection) 5 Ground 6 (No connection) Pin Signal 7 RTS 8 CTS 9 (No connection) 5 RS-232C Communication RS-232C Communication 1 6 2 7 3 8 4 9 5 1 6 2 7 3 8 4 9 5 CONTROL port of the projector RS-232C cable (Cross) - (1) RD (2) TD (3) - (4) GND (5) - (6) RTS (7) CTS (8) - (9) (1) CD (2) RD (3) TD (4) DTR (5) GND (6) DSR (7) RTS (8) DTS (9) RI RS-232C port of the computer Connecting the cable specification shown in the previous page. (2) The projector in creases the setting value on the above setting code. (3) The projector returns the response code `06H' to the computer. Decreasing the projector setting value (Decrement command) (1) The computer sends the decrement code Header + Command data (`05H'+ `00H'+ type (2 bytes) +`00H' + `00H') to the projector. (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code `06H' to the computer. When the projector cannot understand the received command When the projector cannot understand the received command, the error code `15H' is sent back to the computer. Sometimes the projector cannot properly receive the command. In such a case, the command is not executed and the error code `15H' is sent back to the computer. If this error code is returned, send the same command again. [. . . ] If this error code is returned, send the same command again. When the projector cannot execute the received command. When the projector cannot execute the received command, the error code `1cH' + `xxxxH' is sent back to the computer. [. . . ]