User manual HITACHI CP-SX1350W

[. . . ] Projector LENS SHIFT BNG COMPONENT S-VIDEO RGB INTER M1-D INPUT KEYSTONE SEARCH RESET FOCUS ZOOM User's Manual - Operating Guide Thank you for purchasing this projector. WARNING Before using the product, please read the "User's Manual Safety Guide" and related manuals to ensure the proper use of this product. After reading them, store them in a safe place for future reference. NOTE · The information in this manual is subject to change without notice. · The manufacturer assumes no responsibility for any errors that may appear in this manual. [. . . ] : Down memo To finish this operation, press the ESC button but not the button. (This table is continued to the following page. ) 31 Multifunctional Settings (continued) SCREEN Menu (continued) Item Description Select the TURN ON or the TURN OFF using the / buttons. : TURN ON TURN OFF When the TURN ON is selected, the following message function works. The message of the "AUTO IN PROGRESS" for the auto adjustment. The message of the "NO INPUT IS DETECTED" The message of the "SYNC IS OUT OF RANGE" The message of the "Searching . . . " The message of the "Detecting . . . " The indication of the input signal by input change. The indication of the aspect ratio by changing the aspect ratio. The indication of "FOCUS" by adjusting the focus. The indication of "FREEZE" and "||" while freezing the screen by pressing the FREEZE button. memo When the TURN OFF is selected, please remember if the picture is freezing. Do not mistake freezing for a malfunction. Select the EXECUTE using the button to reset the SCREEN menu items. : EXECUTE CANCEL The items of the SCREEN menu are collectively returned to the initial setting. MESSAGE RESET How to register your picture as the MyScreen MyScreen is pointed on the SCREEN menu. Press the button MyScreen Do you start capturing this picture? The MyScreen menu appears. Do you capture the picture from the current screen?If the ESC/RESET button is pressed . . . ESC :NO ENT :YES NO: Press the ESC/RESET button YES: Press the ENTER button The picture freeze and the frame for capturing appears. Move the frame to the position of the picture which you want to use, using / / / buttons, and press the ENTER button to register. My Screen MyScreen Move the capture area as you want. Just when the picture registration is completed the registered screen and the message of the right is displayed for a few seconds. If the picture registration failed, the message of the right is displayed for a few seconds. 45% MyScreen registration is finished. A capturing error has occurred. Please try again. 32 Multifunctional Settings (continued) OPTION Menu With the OPTION menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. Item VOLUME Adjust the volume using the High Low / Description buttons. : MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK : SELECT VOLUME SPEAKER IR REMOTE IR REMOTE ID LAMP TIME FILTER TIME SERVICE RESET 16 TURN ON 1: 2: 3: ALL 1234 h 4321 h SPEAKER Select the TURN ON or the TURN OFF using the / buttons. : TURN ON TURN OFF When the TURN ON is selected, the built-in speaker works. Select a remote sensor using the / button (1), then switch it using the ENTER button (2). [. . . ] Run a command. 7 RS-232C Communication (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (`02H'+`00H'+ type (2 bytes)+`00H'+`00H') from the computer to the projector. (2) The projector returns the response code `1DH'+ data (2 bytes) to the computer. Changing the projector settings (Set command) (1) Send the setting code Header + Command data (`01H'+`00H'+ type (2 bytes) + setting code (2 bytes)) from the computer to the projector. (2) The projector changes the setting based on the above setting code. (3) The projector returns the response code `06H' to the computer. Using the projector default settings (Reset Command) (1) The computer sends the default setting code Header + Command data (`06H'+`00H'+ type (2 bytes) +`00H'+`00H') to the projector. [. . . ]