User manual HITACHI CP-X380W

[. . . ] CP-X380W USER'S MANUAL Please read this user's manual thoroughly to ensure correct usage through understanding. TECHNICAL REGULATORY NOTICES ENGLISH Liquid Crystal Projector Liquid Crystal Projector Thank you for purchasing this liquid crystal projector. WARNING · Please read the accompanying manual "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. NOTE · The information in this manual is subject to change without notice. [. . . ] Clear AUTO OFF: Select STOP (0 min. ) with the button. When STOP is selected the system does not enter the standby mode even if no signal is received. SYNC ON G Valid: Select TURN ON with the button. SYNC ON G Invalid: Select TURN OFF with the button. SYNC ON G · May not be displayed correctly with some input signals when SYNC ON G is valid. In such cases, remove the signal connector so that no signal is received, set SYNC ON G to invalid, and reconnect the signal. WHISPER Set / Crear WHISPER Mode: Press the / button. When the WHISPER is selected, the WHISPER mode is active. In the WHISPER mode, acoustic noise level from the unit is reduced, and brightness level on screen is a little lower. ENGLISH-15 ENGLISH Options Menu OPERATIONS (continued) No Signal Menu The same adjustments and settings are available as with the Image and Options menus when the MENU button is pressed during display of the "NO INPUT IS DETECTED ON ***" or "SYNC IS OUT OF RANGE ON ***" message while no signal is received. Select an item with the and buttons, and start or stop operation with the and buttons. VOLUME BLANK MIRROR START UP MENU COLOR LANGUAGE AUTO OFF SYNC ON G WHISPER 16 Table 8. No Signal Menu Item Reduce VOLUME Description Increase · When this function is used, audio input is automatically switched to video. The audio input can be switched by moving the DISK PAD left and right during the display of the volume adjustment bar. The volume adjustment bar is displayed by pressing VOLUME / button. Select Blank Screen Color: Select the color with the BLANK MIRROR / button. · When the blank mode is set with BLANK ON, by absence of a signal, or by input of a non-standard signal, the image is cleared and the complete screen is displayed in the selected color. Select Mirror Status: Select the mirror status with the / button. button. START UP Setup Initial Screen Display: Select the TURN ON with the Clear Initial Screen Display: Select the TURN OFF with the · Note that if TURN OFF is selected the blank screen is displayed in blue when there is no signal. MENU COLOR LANGUAGE AUTO OFF Select Menu Background Color: Select the color with the / button. Select Menu Display Language: Select the language with the / button. Set AUTO OFF: Set 1~99 minutes with the / button. The system automatically enters the standby mode when a signal is not received for the set time. Clear AUTO OFF: Select the STOP (0 min. ) with the button. When the STOP is selected the system does not enter the standby mode even if no signal is received. SYNC ON G Valid: Select the TURN ON with the button. SYNC ON G Invalid: Select the TURN OFF with the button. · May not be displayed correctly with some input signals when the SYNC ON G is valid. In such cases, remove the signal connector so that no signal is received, set the SYNC ON G to invalid, and reconnect the signal. SYNC ON G WHISPER Set / Crear WHISPER Mode: Press the / button. When the WHISPER is selected, the WHISPER mode is active. In the WHISPER mode, acoustic moise level from the unit is reduced, and brightness level on screen is a little lower. ENGLISH-16 MAINTENANCE HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE Contact your dealer before replacing the lamp. For the optional lamp, see the item "Optional Parts" of the Table 12. [. . . ] (3) The projector returns the response code `06H' to the computer. When a command sent by the projector cannot be understood by the computer When the command sent by the projector cannot be understood, the error command `15H' is returned by the computer. Some times, the projector ignores RS-232C commands during other works. If the error command `15H' is returned, please send the same command again. When data sent by the projector cannot be practice When the command sent by the projector cannot be practiced, the the error code `1cH' +`xxxxH' is returned. When the data length is greater than indicated by the data length code, the projector will ignore the excess data code. [. . . ]