User manual HITACHI CP-X417WF

[. . . ] Projector CP-X417 User's Manual (detailed) Operating Guide Thank you for purchasing this projector. WARNING WARNING CAUTION NOTE Trademark acknowledgment 1 Read this Safety Guide first. Projector User's Manual - Safety Guide Thank you for purchasing this projector. WARNING · Before using, read these user's manuals of this projector to ensure correct usage through understanding. After reading, store them in a safe place for future reference. Incorrect handling of this product could possibly result in personal injury or physical damage. [. . . ] Using the Live Mode 3. 4 Passcode connection (continued) changes. authority. [OK] go back to the item 3. 3. 3 Connecting to the 31 network 3. 3. 1 Starting the "Live Viewer 3" 26 Following the instruction by the network [Connect]. NOTE is currently not in use. 35 3. Using the Live Mode 3. 4 Passcode connection (continued) The message comes up when the network [Exit] on the main menu to go back to the item 3. 3. 3 Connecting to 31 the network another network connection. [Yes] 3. 6 destination 50 [No] on the main menu to go back to the item 31 3. 3. 3 Connecting to the network 36 3. Using the Live Mode 3. 4 Passcode connection (continued) 34 32 Wireless LAN 40 *1 *2 *3: ********** *4: 255. 255. 255. 128 [Connect]. connection to your destination *1 *2 *3 50 40 The encryption key is always shown as "********** *4 37 3. Using the Live Mode 3. 4 Passcode connection (continued) The projector connected to an access point by a LAN cable *1 *2: ********** *3 *4: 255. 255. 255. 128 [Connect]. 50 *1 *2 to check the encryption key that is set in the projector. The encryption key is always shown as "********** *3 *4 40 38 3. Using the Live Mode 3. 4 Passcode connection (continued) The projector connected to an access point by the wireless LAN the projector. *1 *2 *3: ********** *4: 255. 255. 255. 128 [Connect]. 50 *1 *2 *3 The encryption key is always shown as "********** *4 40 39 3. Using the Live Mode 3. 4 Passcode connection (continued) Wired LAN projector. *1: 255. 255. 255. 128 [Connect]. connection to your destination *1 50 NOTE the projector to show the menu on screen. Using the Live Mode There are 3 options for the manual · History with the projector. 60 . [Connect]. connection to your destination NOTE 50 mouse. 41 3. Using the Live Mode 3. 5. 2 History connection settings when connecting to the projector as projector. Using the Live Mode All setting for the network connection between Manually]. Wireless LAN 44 46 45 Wired LAN 47 43 3. Using the Live Mode *1 *2: ********** [Next]. 50 *1 *2 The encryption key is always shown as "********** 40 44 3. Using the Live Mode The projector connected to an access point by a LAN cable *1 *2: ********** [Next]. the projector. 50 *1 *2 to check the encryption key that is set in the projector. [. . . ] Connection ID Random value from 0 to 255 (This value is attached to the reply data). 12 Command Control via the Network (continued) 7. Reply Data The connection ID (the data is same as the connection ID data on the sending data format) is attached to the Network control commands reply data. ACK reply: `06H' + `xxH' NAK reply: `15H' + `xxH' Error reply: `1CH' + `xxxxH' + `xxH' Data reply: `1DH' + `xxxxH' + `xxH' Projector busy reply: `1FH' + `xxxxH' + `xxH' Authentication error reply: `1FH' + `0400H' + `xxH' (`xxH' : connection ID) Automatic Connection Break The TCP connection will be automatically disconnected after there is no communication for 30 seconds after being established. Authentication The projector does not accept commands without authentication success when authentication is enabled. The projector uses a challenge response type authentication with an MD5 (Message Digest 5) algorithm. [. . . ]