User manual HITACHI CP2892TAN

[. . . ] · Allow space for air to pass freely through ventilation holes on the top, sides and bottom of the TV. · Make sure the TV is at room temperature before switching it on. · Check that your mains electricity supply is suitable for the TV, 210-240V at 50Hz. · Unplug the receiver from the wall sockets during thunderstorms or when the TV will not be used for a long time. [. . . ] EUROPE 3P58 83041010-GB 24 Additional features Switching the TV set to stand-by with a timer 1 Press the MENU button (located under the lid). _________________________________________________________________________ 2 Select the option "Timers" and confirm with the OK button. _________________________________________________________________________ 3 Select the required timer function and follow instructions on the screen. Timers Sleep Timer You can select the time after which the TV set will switch off to stand-by. If you want to cancel the timer, select OFF. Off timer Off timer switches the TV set off to the stand-by mode if no remote control button has been pressed for 3 hours. If you select ON, "Off timer" is activated every time you switch the TV set on. If you don't want to use this function at all, select OFF and press the OK button. Sleep timer Off timer Go back 1h 45min OFF Store » Front panel lock When the front panel buttons are locked, the TV set can only be operated using the remote control. 1 Press the MENU button (under the lid). _________________________________________________________________________ 2 Select the option "Front panel lock" and press the OK button. _________________________________________________________________________ Press the cursor button to right to set the lock ON or OFF. _________________________________________________________________________ 3 4 Panel lock Front panel lock Go back ON Store » Store by pressing the OK button. Parental lock When a programme is locked, it cannot be viewed without entering a code. The code is a 4-digit number, selected by the user when locking the programme. ________________________________________________________________________ 2 Press the red button to show the Sound settings menu. ________________________________________________________________________ 3 Use the cursor buttons to adjust start-up volume or balance. ________________________________________________________________________ 4 If you want to store the changed values in the memory, press the OK button. These adjustments affect all programme channels. 3P58 83041010-GB 26 Sound and picture controls Picture set-up Storing new preferred settings Stored picture adjustments affect all programme channels. 1 Press the yellow button twice. _________________________________________________________________________ Adjust the required setting with the cursor buttons. _________________________________________________________________________ 2 3 Preferred settings Brightness Contrast Colour Go back Store » If you want to store the changes, press the OK button. Changing display set-up and the menu language 1 Press the yellow button to select the Vision menu. _________________________________________________________________________ Press the red button to select the Display set-up menu. _________________________________________________________________________ Vision Settings PREFERRED Store Display set-up Preferred settings » Go back 2 3 Change the settings with the cursor buttons. Settings available in this menu: Program number - Permanent display of programme number. Menu language - Screen display language selection. Tint - Colour temperature adjustment (red-blue balance). [. . . ] Code 001 002 003 004 005 Code Operating your VCR/DVD For VCR hold the VCR button (under the lid) down and simultaneously press the required function button. For DVD hold the button which is programmed for DVD use (VCR or SAT) down and simultaneously press the required function button. The list below is meant to be a guideline for the most common functions. U 0. . . 9 Cursor up/down Red Green Yellow Blue REC STOP Switching on/off Entering a programme number (VCR) Selecting a programme number (VCR) Stop Rewind Fast forward Play Recording (VCR) Pause (DVD) 001 002 003 004 005 Code 006 VCR Akai Finlux, Hitachi Nokia, Luxor, Salora, Sanyo Nokia, Finlux, Luxor, Salora, Sharp Finlux, Philips Satellite receiver Nokia, Finlux, Luxor, Salora Finlux SR5800, SR5750 Finlux SR4200 Nokia, Luxor, Salora Pace DVD player Akai 31 If your device does not respond to any of the above code numbers, the remote control unit cannot be used to control your device. Operating your satellite receiver Hold the SAT button (under the lid) down and simultaneously press the required function button. [. . . ]