User manual HITACHI CPL500A

[. . . ] Should the fuse need to be replaced, an ASTA or BSI approved BS 1362 fuse must be used of the same rating. If the fuse cover is detachable never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug. Fuse covers are available from your dealer. [. . . ] It works when the projector is connected to DDC (Display Data Channel) ready computer that is running an operating system software that incorporates plug & play functionality. (Only RGB 1) 14 Basic operations (continued) FREEZE FUNCTION 1 2 Press the FREEZE button. The display image stops. A mark appears at the lower right of the screen for about 3 seconds during the FREEZE function. 1, 2 MAGNIFY VOLUME OFF POSITION ON LASER [TO RELEASE FREEZE] Press the FREEZE button. The freeze function is cancelled. Furthermore, a seconds or so when FREEZE is released. mark appears at the bottom of the screen for 3 Caution · When the FREEZE Button is pressed, FREEZE and RELEASE can function alternately. · What is more, FREEZE is released when an input selector button is pressed or when the display mode of a personal computer is switched over during display. · The POSITION ON icon is not displayed during freeze. Also, scrolling using DISK PAD operation is not possible. · When a still picture signal is given as input and the freeze function is ON, do not forget to cancel the freeze function. · Some set up items can not be adjusted during freeze. (See page 17) MAGNIFYING FUNCTION It is possible to display a partially magnified picture. Some items can not be adjusted during freeze or during magnify. (Please refer to the above table. ) < Manual Operation > Adjust optional items manually. (1) Use the MENU buttons on the unit or the DISK PAD on the remote control to move the green cursor to the number of the item you wish to adjust. (2) With the green cursor on the number, use the MENU buttons on the unit or the DISK PAD on the remote control to raise or lower the value. SETUP INPUT IMAGE OPT. VOLUME BRIGHT CONTRAST V POSIT H POSIT H PHASE H SIZE COLOR BAL 121 57 7 800 R AUTO B 17 ENGLISH Adjustments and functions (continued) < AUTO-adjustment > The projector will automatically adjust four items (V POSIT, H POSIT, H PHASE, H SIZE, White level). When AUTO is selected (the cursor is moved from Manual Operation towards the right) the AUTO Confirm screen shown below will be displayed. < AUTO-adjustment Confirm Screen > While the AUTO confirmation screen is displayed as illustrated on the upper right, if you shift the cursor upward and select AUTO, the projector will perform auto-adjustment. It will become as illustrated on the lower right. If CANCEL is selected for three seconds, or if the RESET button on either the unit or the remote control is pressed, the green cursor will return to the value for the selected item (Manual Operation) SETUP INPUT IMAGE OPT. VOLUME BRIGHT CONTRAST 123 V POSIT AUTO 111 H POSIT CANCEL 31 H PHASE 1024 H SIZE R COLOR BAL AUTO B < During AUTO-adjustment > At the lower right of the screen the word <AUTO> will flash in green letters. When the auto-adjustment is completed the word <AUTO> will disappear. The auto-adjustment of the white level is cancelled by input switching and signal mode change. Caution AUTO · When start up screen is displayed ("NO INPUT IS DETECTED" or "SYNC IS OUT OF RANGE" is displayed), SETUP menu items other than VOLUME cannot be set. · TINT cannot be adjusted with PAL/SECAM video signal input. [. . . ] If the lamp does not light because it is still automatically turned off, contact your dealer. *2 If temperature inside the unit increases because of blocked vets, the lamp may go off for protection, and the LAMP indicator will turn red. Should this happen, turn off the main switch, wait until the set cools down (about 45 minutes), then again turn on the main switch. 32 When you think something wrong Check the following again before asking for service. If the trouble cannot be recovered, consult your dealer. Phenomena Cause Check point Page Power cannot be turned on. ·Inside the projector too hot. [. . . ]