User manual HITACHI CPS235

[. . . ] Projector CP-S235 User's Manual - Operating Guide Thank you for purchasing this projector. WARNING Before using, read the "User's Manual - Safety Guide" and these manuals to ensure correct usage through understanding. After reading, store them in a safe place for future reference. NOTE · The information in this manual is subject to change without notice. [. . . ] · When the set time passes without a valid signal (there is no signal, or the signal is out of specifications), the projector lamp automatically goes off, and the POWER indicator begins blinking. Please refer to the section "Turning OFF The Power" of "Power ON/OFF" about the turning off. Automatically Signal Search: TURN ON TURN OFF · If the TURN ON is selected under this item when no signal input is detected, the projector begins searching for an input signal. When an input signal is detected the projector will cease searching and the picture will appear. · The priority of a search is as follows: RGB VIDEO S-VIDEO COMPONENT VIDEO · If the projector is unstable to find an input signal at any of its ports, it will return to the state it was in prior to the search. Reset the AUTO Menu Items: Selecting the EXECUTE performs this function. EXECUTE CANCEL · The items of the AUTO menu are collectively returned to the initial setting. Note that the item ADJUST is not reset. MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION : SELECT ADJUST POWER OFF SEARCH RESET 0 min TURN ON ADJUST POWER OFF SEARCH RESET 29 Multifunctional Settings (continued) SCREEN Menu With the SCREEN menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. Item Description Select a Blank Screen Color: BLUE WHITE BLACK · The blank screen of selected color is displayed by pressing the BLANK button. Please refer to the section "Temporarily Blanking The Screen" of "Operating" about the screen blanking. Select the Start Up Screen: TURN ON TURN OFF · If the TURN ON is selected when there is no signal or the detected signal is out of specifications, the blank screen is displayed. Adjust a Menu Position: Pressing the or ENTER button start adjusting, Up MENU POSITION Left Right MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION : SELECT BLACK BLANK TURN ON START UP MENU POSITION MESSAGE TURN ON RESET BLANK START UP Down · The button does not finish this item. When you want to return to the previous display, please press the ESC button. Select the Message Mode: TURN ON TURN OFF · When the TURN OFF is selected, the following message functions are disabled: The message of "AUTO IN PROGRESS" The message of "NO INPUT IS DETECTED" The message of "SYNC IS OUT OF RANGE" The message while being searched for an input signal, "Searching . . . . . " The message when an input signal is detected, "Detecting . . . . . " The indication of the input signal by input change. Reset the SCREEN Menu Items: Selecting the EXECUTE performs this function. EXECUTE CANCEL · The items of the SCREEN menu are collectively returned to the initial setting. MESSAGE RESET 30 Multifunctional Settings (continued) OPTION Menu With the OPTION menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. Item VOLUME Adjust Volume: High Description Low MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION : SELECT VOLUME SCREEN TYPE LAMP TIME FILTER TIME RESET 16 4:3 1234h 21h SCREEN TYPE Select the Screen Type: 4:3 16:9 16:9 16-9 · Please select the screen type used and the picture position in case of 16:9. This selection is used as basic information for a suitable display. This function should be performed before other picture adjustment. To begin the operation of this item, please press the button of the projector or the RESET button of the remote control for 3 seconds. Reset the Lamp Timer: Selecting the RESET performs this function. RESET CANCEL · The numerical value of four digits shown on this menu is the projector use time since the last RESET operation of this item. [. . . ] Correctly connect the connection cables. Pictures are displayed, but no sounds are heard. The volume setting has been set at (or adjusted to) an extremely low level. Adjust the VOLUME setting to a higher level. [. . . ]