User manual HITACHI CPX1403MS

[. . . ] Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 10) 11) 12) 13) 14) 15) Unplug this apparatus during lightning storms or when unused for long periods of time. [. . . ] Turn the control clockwise to increase and counterclockwise to decrease. 5. CONTRAST Adjust the CONTRAST control for the desired overall contrast. Proper adjustment will allow maximum gradations between the darkest and lightest picture areas. Turn the control clockwise to increase and counterclockwise to decrease. 6. VOLUME Adjust the VOLUME control for the desired audio level. Turn the control clockwise to increase and counterclockwise to decrease. 7. VIDEO 1 TACT SWITCH Set the switch to VIDEO 1 if the camera jack is used. 8. VIDEO 2 TACT SWITCH Set the switch to VIDEO 2 if the camera jack is used. 9. S-VIDEO TACT SWITCH Set the switch to S-VHS if the S-VIDEO jack is used. 10. POWER SWITCH Press to turn the monitor ON. The POWER LAMP above the switch will illuminate. 11. POWER LED LAMP Power lamp indicates the power is on. 12. To prevent electrical shocks and fire hazards, do not use any other power source. 13 16. VIDEO INPUT & OUTPUT CONNECTORS These BNC connectors permit looping of a video signal in those installations where it is desirable to display the video signal on more than one monitor. A standard 1. 0 Vp-p video signal applied to the VIDEO INPUT will also appear at the VIDEO OUTPUT. Use coaxial cables with BNC type plugs for these connections. 17. S-VIDEO JACK If the camera or other video source outputs an S-VIDEO signal, connect it directly to this jack. 18 23. AUDIO INPUT & OUTPUT CONNECTORS Connect an RCA cable between these jacks and the audio output jack of a camera or VCR. 4 POSSIBLE CONNECTIONS Read the installation/operation manual thoroughly before connecting equipment. Turn off the power source before connecting the monitor and external equipment. VIDEO 1 Connection (Select input VIDEO 1 button) Audio Audio signal cable Video Video signal cable Video camera VCR Audio Video Video Monitor VIDEO 2 Connection (Select input VIDEO 2 button) Audio Audio signal cable Video Video signal cable Video camera VCR Audio Video Video Monitor S-VIDEO connection (Select input S-VIDEO button) Audio Audio signal cable Video camera VCR Audio Y/C (S-VHS) S-VHS Signal cable 5 SAFETY INSTRUCTIONS IMPORTANT SAFEGUARDS All the safety and operating instructions should be read before the monitor is operated. Retain the instructions for future reference. HEED WARNINGS All warnings on the monitor and in the operating instructions should be adhered to. FOLLOW INSTRUCTIONS All operating instructions should be followed. [. . . ] Refer all servicing to qualified service personnel. 6 SPECIFICATIONS Picture Tube Power Source Power Consumption System Sound output Resolution Speaker Terminals 14-inch diagonal, 90 deflection angle 100-240V AC, 50/60 Hz 45 Watts PAL / NTSC 1. 0 W Center resolution : 450 TV lines or more 3 W , 70 mm X 40 mm Video input level/impedance: 1. 0 Vpp/75 Video output level/impedance: 1. 0 Vpp/75 S-VIDEO INPUT Audio input level/impedance: 0. 3 Vrms/25K Audio output level/impedance: 0. 3 Vrms/4. 7K 13. 8 in 12. 9 in 14. 6 in (350 328 371 mm) Approx. 30. 9 lb (14Kg) 0-40 (32-106 F) Dimensions(W H D) Weight Operating Temperature Design and specifications are subject to change without notice. Warning This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 7 Hitachi, Ltd. Tokyo, Japan International Sales Division THE HITACHI ATAGO BUILDING, No. [. . . ]