User manual HITACHI CP-X205W

[. . . ] Projector CP-X205/CP-X305 User's Manual (detailed) Operating Guide Thank you for purchasing this projector. WARNING Before using this product, please read all manuals for this product. Be sure to read "Safety Guide" first. After reading them, store them in a safe place for future reference. About this manual Various symbols are used in this manual. [. . . ] · When the projector is placed on the level (about ±0°), this function may not work. · When the projector is inclined to near ±30 degree or over, this function may not work well. · This function will be unavailable when the Transition Detector is on (49). Using the / buttons corrects the vertical keystone distortion. Shrink the top of the image ó Shrink the bottom of the image · The adjustable range of this function will vary with the type of input signal. For some input, this function may not work well. · This function will be unavailable when the Transition Detector is on (49). AUTO KEYSTONE EXECUTE KEYSTONE (continued on next page) 34 SETUP menu SETUP menu (continued) Item WHISPER Description Using the / buttons turns off/on the whisper mode. NORMAL ó WHISPER · When WHISPER is selected, acoustic noise and screen brightness are reduced. Using the / buttons switches the mode for mirror status. MIRROR NORMAL ó H:INVERT ó V:INVERT ó H&V:INVERT If the Transition Detector is TURN ON and MIRROR status is changed, Transition Detector Alarm (49) will be displayed when projector is restarted after the power switch is turned off. VOLUME SPEAKER Using the / buttons adjusts the volume. High ó Low Using the / buttons turns on/off the built-in speaker. TURN ON ó TURN OFF When TURN OFF is selected, the built-in speaker does not work. (1) Choose a picture input port using the / buttons. COMPUTER (IN)1 ó COMPUTER (IN)2 VIDEO ó S-VIDEO ó COMPONENT (2) Select the audio port to be interlocked with the input port using the / buttons. óó3ó When is selected to an input port, any audio ports do not work interlocking with the input port. AUDIO 35 SCREEN menu SCREEN menu From the SCREEN menu, items shown in the table below can be performed. Select an item using the / cursor buttons, and press the cursor button or ENTER button to execute the item. Then perform it according to the following table. Item Description Using the / buttons switches the OSD (On Screen Display) language. ENGLISH FRANÇAIS DEUTSCH ESPAÑOL ITALIANO TÜRKÇE NORSK POLSKI NEDERLANDS SUOMI PORTUGUÊS SVENSKA LANGUAGE MENU POSITION Using the /// buttons adjusts the menu position. To quit the operation, press MENU button on the remote control or keep no operation for about 10 seconds. Using the / buttons switches the mode for the BLANK screen. The BLANK screen is a screen for the temporarily blanking feature (21). It is displayed by pressing BLANK button. MyScreen ó ORIGINAL ó BLUE ó WHITE ó BLACK BLANK MyScreen ORIGINAL BLUE, WHITE, BLACK Feature Screen can be registered by the MyScreen item (38). Screen preset as the standard screen. Plain screens in each color. · To avoid remaining as an afterimage, the MyScreen or ORIGINAL screen will change to the plain black screen after several minutes. (continued on next page) 36 SCREEN menu SCREEN menu (continued) Item Description Using the / buttons switches the mode for the start-up screen. [. . . ] In such a case, disconnect the power cord, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again. Shutting the projector down Only when the projector can not be turned off by usual procedure (15), please push the shutdown switch using a pin or similar, and disconnect the power plug from the power outlet. Before turning it on again, wait at least 10 minutes to make the projector cool down enough. BATTERY Shutdown switch Resetting all settings When it is hard to correct some wrong settings, the FACTORY RESET function of SERVICE item in OPTION menu (44) can reset all settings(except LANGUAGE, FILTER TIME, LAMP TIME, FILTER MESSAGE, NETWORK settings and etc. ) to the 6 factory default. Troubleshooting Phenomena that may be easy to be mistaken for machine defects About the phenomenon confused with a machine defect, check and cope with it according to the following table. Phenomenon Cases not involving a machine defect Reference page The electrical power cord is not plugged in. Correctly connect the power cord. The main power source has been interrupted during operation such as by a power outage (blackout), etc. Power does not come on. Please disconnect the power plug from the power outlet, and allow the projector to cool down at least 10 minutes, then turn the power on again. 12, 15 Either there is no lamp and/or lamp cover, or either of these has not been properly fixed. Please turn the power off and disconnect the power plug from the power outlet, and allow the projector to cool down at least 45 minutes. [. . . ]