User manual HITACHI CP-X308

[. . . ] Projector CP-X308 User's Manual (detailed) Operating Guide Thank you for purchasing this projector. WARNING Before using this product, please read all manuals for this product. Be sure to read "Safety Guide" first. After reading them, store them in a safe place for future reference. About this manual Various symbols are used in this manual. [. . . ] Display the image you want to capture before executing the following procedure. Selecting this item displays a dialog titled "MyScreen". It will ask you if you start capturing an image from the current screen. Please wait for the target image to be displayed, and press the ENTER button when the image is displayed. The image will freeze and the frame for capturing will appear. To stop performing, press the RESET or ESC button. Using the /// buttons adjusts the frame position. Please move the frame to the position of the image which you want to use. The frame may not be able to be moved for some input signals. To start registration, press the ENTER button. To restore the screen and return to the previous dialog, press the RESET or ESC button. When the registration is completed, the registered screen and the following message are displayed for several seconds: "MyScreen registration is finished. " If the registration failed, the following message is displayed: "A capturing error has occurred. Please try again. " · This function cannot be selected when the TURN ON is selected to the MyScreen Lock item (below). · This function cannot be selected when TURN ON is selected to the MyScreen PASSWORD of SECURITY item in OPTION menu (48). Using the / buttons turns on/off the MyScreen lock function. TURN ON ó TURN OFF When the TURN ON is selected, the MyScreen item is locked. Use this function for protecting the current MyScreen. · This function cannot be selected when TURN ON is selected to the MyScreen PASSWORD of SECURITY item in OPTION menu (48). MyScreen MyScreen Lock (continued on next page) 40 SCREEN menu SCREEN menu (continued) Item Description Using the / buttons turns on/off the message function. TURN ON ó TURN OFF When the TURN ON is selected, the following message function works. "AUTO IN PROGRESS" while automatically adjusting "NO INPUT IS DETECTED" "SYNC IS OUT OF RANGE" "Searching. . . " while searching for the input "Detecting. . . " while an input signal is detected The indication of the input signal displayed by changing The indication of the aspect ratio displayed by changing The indication of the PICTURE MODE displayed by changing The indication of the MY MEMORY displayed by changing The indication of "FREEZE" and "II" while the projector is in the FREEZE mode. · If the projector goes into the FREEZE mode while the TURN OFF is selected, the picture on screen is frozen without any messages, which is not a malfunction. (22) Each input port for this projector can have a name applied to it. [. . . ] Please disconnect the power plug from the power outlet, and allow the projector to cool down at least 10 minutes, then turn the power on again. 13, 16 Either there is no lamp and/or lamp cover, or either of these has not been properly fixed. Please turn the power off and disconnect the power plug from the power outlet, and allow the projector to cool down at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again. 64, 65 The signal cables are not correctly connected. Correctly connect the connection cables. 9 ­ 17, 18 Signal source does not correctly work. Neither sounds nor pictures are outputted. Correctly set up the signal source device by referring to the manual of the source device. The input changeover settings are mismatched. Select the input signal, and correct the settings. The BLANK function for pictures and the MUTE function for sounds are working. AV Mute may be active. Refer to the item "Sound does not come out" and "No pictures are displayed" on the next page to turn off the MUTE and BLANK functions. (Continued on next page) 17, 22 73 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Phenomenon Cases not involving a machine defect Reference page 9 7 The signal cables are not correctly connected. Correctly connect the audio cables. The MUTE function is working. Sound does not come out. Restore the sound pressing MUTE or VOLUME button on the remote control. The volume is adjusted to an extremely low level. [. . . ]