User manual HITACHI CP-X340WF

[. . . ] Projector CP-S335W/X340W/X345W/X340WF/X345WF User's Manual ­ Operating Guide Thank you for purchasing this projector. WARNING Before using, read the "User's Manual - Safety Guide" and these manuals to ensure correct usage through understanding. After reading, store them in a safe place for future reference. About this manual Various symbols are used in this manual. The meanings of these symbols are described below. [. . . ] Strong Weak · This item can be selected only at a video signal. Green Red · This item can be selected only at a video signal except for SECAM. Using the buttons / adjusts the sharpness. Strong Weak COLOR TEMP TINT SHARPNESS 26 Multifunctional settings PICTURE Menu (continued) Item Description Using the buttons / switches the progressive mode. TV FILM TURN OFF · This function performs only at an interlaced signal of a VIDEO input, a S-VIDEO input or a COMPONENT VIDEO input of 525i (480i) or 625i (576i) signal. · When the TV or FILM is selected, the screen image will be crisper. The FILM mode is adaptable to the 2-3 Pull-Down system to the conversion. But these may cause a certain defect (for example, jagged line) of the picture at a quick moving object. In such a case, please select the TURN OFF, even though the screen image may lose the crisp. Selecting a mode of MY MEMORY using the buttons / and then pressing the button or the ENTER button performs each function. LOAD1 LOAD2 LOAD3 LOAD4 SAVE4 SAVE3 SAVE2 SAVE1 This projector has 4 numbered memories for adjustment data. Performing the LOAD1, LOAD2, LOAD3 or LOAD4 loads the data on the memory whose number corresponds with the command' s number, and adjusts the picture automatically depending on the data. Performing the SAVE1, SAVE2, SAVE3 or SAVE4 puts the current adjustment data on the memory whose number corresponds with the command's number. PROGRESSIVE MY MEMORY 27 Multifunctional settings IMAGE Menu With the IMAGE menu, items shown in the table below can be performed. Select an item using the cursor buttons / on the projector or remote control, and press the cursor button on the projector or remote control, or the ENTER button on the remote control to progress. Then perform it referring to the following table. Item Description Using the buttons / switches the mode for aspect ratio. At a RGB signal 4:3 16:9 NORMAL At a video signal / no signal 4:3 16:9 SMALL · The NORMAL mode keeps the original aspect ratio of the signal. · At a HDTV signal of 1125i (1080i) or 750p (720p) of COMPONENT VIDEO input, this item can't be selected. · Performing the automatic adjustment initializes the aspect ratio setting. Using the buttons / adjusts the over-scan ratio. Large (It reduces picture) Small (It magnifies picture) · This item can be selected only at a video signal. · When this adjustment is too large, certain degradation may appear at the frame area of the picture. Using the buttons / adjusts the vertical position. [. . . ] The main power source has been interrupted during operation such as by a power outage (blackout), etc. Power does not come on. Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled down, please turn the power on again. 16 Either there is no lamp and/or lamp cover, or either of these has not been properly fixed. Please turn the power off, and allow the unit to cool down at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again. 38, 39 46 Troubleshooting Phenomena that may easily be mistaken for machine defects (continued) Phenomenon Cases not involving a machine defect Reference page 4, 16 10 23, 25 The lens cover is closed. Remove the lens cover. The signal cables are not correctly connected. Correctly connect the connection cables. No pictures are displayed. The brightness is adjusted to an extremely low level. [. . . ]