User manual HITACHI CP-X385

[. . . ] LCD Projector CP-X385W USER'S MANUAL Thank you for purchasing this projector. Vol. 1 (Basic) WARNING · Please read the accompanying manual "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. NOTE · The information in this manual is subject to change without notice. · The manufacturer assumes no responsibility for any errors that may appear in this manual · The reproduction, transmission or use of this document or contents is not permitted without express written authority. [. . . ] Dark pictures may still be incorrectly adjusted. Use a bright screen when adjusting. AUTO MENU KEYSTONE ENTER POSITION ASPECT FREEZE MAGNIFY ON OFF RESET Automatic Adjustment for Video Input The signal type best suited for the respective input signal is selected automatically. This feature is available only if VIDEO is set to AUTO in the INPUT menu. ESC MUTE VOLUME SEARCH NOTE The automatic adjustment operation requires approximately 10 seconds. Also, please note that it may not function correctly with some input signals. 19 CORRECTING KEYSTONE DISTORTIONS STANDBY/ON LASER BLANK 1 Press the KEYSTONE button As illustrated on the right, a dialog will appear on the screen to aid you in correcting the distortion. KEYSTONE KEYSTONE KEYSTONE VIDEO RGB 16 AUTO MENU 2 KEYSTONE ENTER Use the , buttons to select the direction of distortion to correct ( / ) POSITION ASPECT FREEZE MAGNIFY ON OFF RESET ESC MUTE VOLUME 3 Use the distortion , buttons to correct the SEARCH Press the KEYSTONE button again to close the dialog and complete this operation. (Even if you don't do anything, the dialog will automatically disappear after a few seconds. ) Control panel NOTE · This function may not be work well with some types of input signals. · The adjustable range for correcting keystone distortions will vary with the type of input signal. 20 USING THE MAGNIFY FEATURE STANDBY/ON LASER BLANK 1 Press the MAGNIFY (ON) button The projector enters MAGNIFY mode. MAGNIFY ON VIDEO RGB Press the POSITION button, then , , 2 , buttons to select the area touse the and then enlarge press the POSITION button again to confirm your selection POSITION POSITION AUTO MENU KEYSTONE ENTER POSITION ASPECT FREEZE MAGNIFY ON OFF RESET 3 Press the , buttons to zoom in and out of the selected area. Press the MAGNIFY (OFF) button to exit MAGNIFY mode and restore the screen to normal. (The projector will also automatically exit MAGNIFY mode if there is a change in the input signal's state. ) ESC MUTE VOLUME SEARCH NOTE The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT, AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signal's state. FREEZING THE SCREEN ENTER POSITION ASPECT FREEZE MAGNIFY ON OFF RESET 1 Press the FREEZE button The [II] icon appears and the screen will freeze at the current image. Press the FREEZE button again and the [ ] appears as the projector exits FREEZE mode. FREEZE ESC MUTE VOLUME SEARCH NOTE · The projector will automatically exit from FREEZE mode if either the POSITION, VOLUME, MUTE, AUTO, BLANK ON/OFF or MENU ON/OFF feature is used, or, if there is a change in the input signal's state. · If the projector continues projecting the same image for a long time (i. e. you forget to exit FREEZE mode), the image might possibly remain as an afterimage. Do not leave the projector in FREEZE mode for too long. 21 SIGNAL SEARCHING POSITION ASPECT FREEZE MAGNIFY ON OFF RESET 1 Press the SEARCH button When you press the SEARCH button, the projector begins searching for input signals. If it detects an input signal, the search will cease and the projector will project the detected signal. If the projector is unable to find an input signal at any of its ports, it will return to the state it was in prior to the search. SEARCH ESC MUTE VOLUME SEARCH RGB IN 1 RGB IN 2 VIDEO IN S-VIDEO IN COMPONENT VIDEO SELECTING THE ASPECT RATIO AUTO MENU 1 KEYSTONE ENTER Press the ASPECT button ASPECT POSITION ASPECT FREEZE MAGNIFY ON OFF RESET ESC MUTE VOLUME RGB IN 1, RGB IN 2, COMPONENT VIDEO (HDTV signals : 1125i (1035i/1080i), 750p) 4:3 16:9 VIDEO IN, S-VIDEO IN, COMPONENT VIDEO (Non-HDTV signals : 525i, 525p, 625i) 4:3 16:9 SMALL SEARCH TEMPORARILY BLANKING THE SCREEN STANDBY/ON LASER BLANK 1 Press the BLANK button The input signal screen is shut off, and a blank screen appears. You can set the blank screen using the menu (from the SCREEN menu, select BLANK). Press the BLANK button again to remove the blank screen, and return to the input signal screen. BLANK VIDEO RGB AUTO 22 USING THE MENU FUNCTIONS STANDBY/ON LASER BLANK 1 Press the MENU button MENU VIDEO RGB The menu display appears on the screen. The projector has the following menus: MAIN, PICTURE-1, PICTURE-2, INPUT, SCREEN, and OPTION. The current settings of the items that can be manipulated via the selected menu appear. 2 AUTO MENU KEYSTONE ENTER POSITION ASPECT FREEZE MAGNIFY ON OFF RESET / Select a menu using the buttons, then press the or ENTER button. The display of the selected menu appears. Adjusting SHARPNESS] Use the / buttons to select PICTURE-1, then press the or ENTER button. MENU MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION COLOR BAL R COLOR BAL B SHARPNESS COLOR TINT ­1 +1 ­1 +1 ­1 ESC MUTE VOLUME ENTER : SELECT 3 Select an item using the or ENTER button. / buttons, then press the The operation display of the selected item appears. To adjust a numerical value, press the or ENTER button again to switch to the single menu (small display showing only the operation display area). Adjusting SHARPNESS] Use the / buttons to select SHARPNESS, then MENU press the or ENTER button. MAIN COLOR BAL R PICTURE-1 PICTURE-2 INPUT SCREEN OPTION COLOR BAL B SHARPNESS COLOR TINT 0 : SELECT ENTER 4 Press the / buttons to adjust the level. Press the MENU button to hide the menu and finish your operation. [. . . ] · When the lamp has been replaced after the message of "CHANGE THE LAMP . . . THE POWER WILL TURN OFF AFTER 0 hr. " is displayed, or the LAMP indicator is red, complete the following operation within 10 minutes of switching power ON. NOTE · The LAMP indicator is also red when the lamp unit reaches high temperature. Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again. If the LAMP indicator is still red, replace the lamp. 26 THE AIR FILTER Caring for the air filter The air filter should be cleaned about every 100 hours. If the LAMP indicator and TEMP indicator blink red simultaneously, or a message prompts you to clean the air filter when you turn on the unit, the filter needs to be cleaned. [. . . ]