User manual HITACHI CPX885W

[. . . ] CP-X880W / CP-X885W USER'S MANUAL, Vol. 1 Please read this user's manual thoroughly to ensure correct usage through understanding. USER'S MANUAL, Vol. 2 TECHNICAL REGULATORY NOTICES ENGLISH Liquid Crystal Projector LCD Projector CP-X880/CP-X885 USER'S MANUAL Thank you for purchasing this projector. Vol. 1 (Basic) WARNING · Please read the accompanying manual "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. [. . . ] Select Picture Position (for 16:9/SMALL Picture): TOP CENTER BOTTOM Select Gamma Mode: NORMAL CINEMA Select Mirror Status: NORMAL H:INVERT Select Menu Language: ENGLISH FRANÇAIS ITALIANO NORSK POTUGUÊS DYNAMIC V:INVERT DEUTSCH NEDERLANDS H&V:INVERT ESPAÑOL PICT. POSIT. GAMMA MIRROR LANGUAGE 2 PICTURE-1 Menu With the PICTURE-1 menu, the five items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table. MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION WIRELESS : SELECT COLOR BAL R COLOR BAL B SHARPNESS COLOR TINT 12 Example : PICTURE1 Menu (COLOR BAL R) PICTURE-1 Menu Item COLOR BAL R COLOR BAL B SHARPNESS COLOR TINT Description Adjust Red Color Balance: Dark Adjust Blue Color Balance: Dark Light Light Soft Adjust Sharpness (for VIDEO/S-VIDEO): Clear Adjust COLOR (for VIDEO/S-VIDEO/COMPONENT VIDEO): Dark Light Adjust Tint (for VIDEO/S-VIDEO): Green Red PICTURE-2 Menu With the PICTURE-2 menu, the five items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table. MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION WIRELESS : SELECT V POSITION H POSITION H PHASE H SIZE OVER SCAN 12 Example : PICTURE2 Menu (V POSITION) PICTURE-2 Menu Item V POSITION H POSITION H PHASE Description Adjust Vertical Position (for RGB): Up Adjust Horizontal Position (for RGB): Left Down Right Adjust Horizontal Phase (for RGB/COMPONENT VIDEO): Right Left · Adjust to eliminate flicker. Adjust Horizontal Size (for RGB): Large Small · If the horizontal size adjustment is excessive, the image may not be displayed correctly. In such a case, initialize H SIZE with the RESET button. Select Over-scan Ratio (for VIDEO/S-VIDEO/COMPONENT VIDEO): LARGE MIDDLE SMALL · If you select LARGE, you may note streaking on the top and bottom of the screen, or flicker. If this is irritating, we suggest you select SMALL. H SIZE OVER SCAN 3 MULTIFUNCTIONAL SETTINGS (continued) INPUT Menu The three Input menu items listed in the table below can be manipulated. For RGB input, the reception signal's horizontal and vertical frequency is displayed on the initial menu screen. Use the table below as a guide for operation. MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION WIRELESS : SELECT BNC VIDEO HDTV SYNC ON G P. POSIT RGB COMPONENT INPUT Menu Item Description Example : INPUT Menu (BNC) BNC Pin (R/CR/PR, G/Y, B/CB/PB, H, V) function selection: BNC (RGB) BNC (COMPONENT) (R) (G) (B) (H) (V) BNC (CR/PR) (Y) (CB/PB) ( - ) ( - ) (Pins for RGB) (Pins for COMPONENT) Selecting BNC (RGB) allows the 5 RGB2 pins (R/CR/PR, G/Y, B/CB/PB, H, V) to be used as RGB signal BNC input as-is. Selecting BNC (COMPONENT) allows the 3 leftmost RGB2 pins (R/CR/PR, G/Y, B/CB/PB) to be used as the COMPONENT VIDEO input CR/PR, Y, and CB/PB pins. Select Mode of Signal Type (for VIDEO/S-VIDEO): AUTO M-PAL NTSC N-PAL are enabled, and is PAL SECAM NTSC4. 43 When AUTO is selected, the video/ S-video input function under ADJUST ( 5 VIDEO executed simultaneously so that the optimum signal mode is selected from among the modes listed above. Use this function if the image becomes unstable with VIDEO/S-VIDEO. The image becomes irregular, or lacks color. ) · AUTO mode may not function correctly with a PAL60 signal and certain other signals. · The AUTO mode operation requires approximately 10 seconds. · For COMPONENT VIDEO, the signal type is identified automatically even if this function is inactive. For a HDTV signal, refer to the item HDTV below. HDTV Select HDTV Signal Mode: 1080i 1035i · If the selected HDTV mode is incompatible with the input signal, the picture may be distorted. On/Off SYNC ON G Mode: TURN ON TURN OFF Selecting TURN ON turns on the SYNC ON G mode. The SYNC ON G mode allows reception of SYNC on G. · In the SYNC ON G mode, the picture may be distorted with certain input signals. In such a case, remove the signal connector so that no signal is received and turn SYNC ON G off, and then reconnect the signal. [. . . ] (3) The projector returns the response code `06H' to the computer. When a command sent by the projector cannot be understood by the computer When the command sent by the projector cannot be understood, the error command `15H' is returned by the computer. Some times, the projector ignores RS-232C commands during other works. If the error command `15H' is returned, please send the same command again. When data sent by the projector cannot be practice When the command sent by the projector cannot be practiced, the the error code `1cH' +`xxxxH' is returned. When the data length is greater than indicated by the data length code, the projector will ignore the excess data code. [. . . ]