Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HITACHI CPX940E. We hope that this HITACHI CPX940E user guide will be useful to you.
Lastmanuals help download the user guide HITACHI CPX940E.
Detailed instructions for use are in the User's Guide.
[. . . ] -1 About Trademarks
I
q VGA and XGA are trademarks of IBM (International Business Machines Corporation).
q q
Macintosh is registered trademark of Apple Computer Corporation of the U. S. VESA and SVGA are trademarks or registered trademarks of Video Electronics Standards association. Carefully observe the trademarks and registered trademarks of all companies, even when not mentioned.
Q Windows95 and Windows98 are registered trademarks of Microsoft Corporation in the U. S. and other countries.
2
[Safety precaution]
s If any abnormality
q
occurs.
smell or smoke, if
u Do not look directly at the lens when the lamp is lit.
Do not look directly at the lens when the lamp is lit. [. . . ] RGB signal input
influencing
the picture and for
VIDEO signal input m-
Adjustment VOLUME
Item
Details of adjustment
Decrease ~ Increase Bright
Freeze
Magnify
~g;:$
o o o x
x
0 0 0 o o
0 0 0 x x
BRIGHT (BRIGHTNESS) CONTRAST SHARPNESS COLOR TINT
Dark ~
Lower ~
Higher Sharp
soft ~ Less ~ Red ~
Moves the
More Green
x x x x x o
o
x x o x 0
x
x x x x 0
b
V. PHASE H. SIZE COLOR BAL (COLOR BALANCE)
picture up or down. Or automatic control.
Moves the picture left or right. Or automatic control.
Decreases the picture flicker. Or automatic control.
Widens ofNarrow thehorizontal sizeofthepicture. O r
for Red ~
for Blue
0: operation is possible. How to use the SETUP
1. Bar display items (VOLUME,
x: operation is not possible.
menu
BRIGHT etc. ) of the bar display. Some items can not be adjusted
Move the green cursor to the item you wish to adjust, then move the MENU buttons on the unit, or the DISK PAD, to left and right to adjust the length 2. Numerical Use either display items (V POSIT, H POSIT etc. ) manual operation or auto-adjustment. Some items can not be adjusted during freeze or (Please refer to the above table. ) during ffeeze or during magnify. (Please refer to the above table. )
during magni@.
< Manual Operation >
Adjust optional items manually. (1) Use the MENU buttons adjust.
(2) With
m
INPUT IMAGE oPT.
on the `unit or the DISK PAD on the remote
control to move the green cursor to the number of the item you wish to
VOLUME BRIGHT CONTRAST V POSIT
H POSIT H PHASE
the green cursor on the number,
use the MENU buttons control to raise
on the the
H SIZE
COLORBAL
unit or the DISK PAD on the remote value.
or lower
u
~H ~o
~:
AUTO @ m 9 B
1024 J
31
R~
17
Adjustments and functions (continued)
< AUTO-adjustment >
adjust four items (V POSIT, H POSIT, H PHASE, H SIZE, White level). towards the right) the AUTO Confirm The projector will automatically When AUTO is selected (the cursor is moved from Manual Operation screen shown below will be displayed.
Confirm Screen > < AUTO-adjustment While the AUTO confirmation screen is displayed as illustrated on the upper right, if you shift the cursor upward and select AUTO, the projector will perform auto-adjustment. It will become as illustrated on the lower right. If CANCEL is selected for three seconds, or if the RESET button on either the unit or the remote control is pressed, the green cursor will return to the value for the selected item (Manual Operation) < During AUTO-adjustment >
will flash in green
kE@
INPUTIMAGE OPT
VOLUME BRIGHT CONTRAST
~;,
m=!
R~ B
COLORBAL d
a
At the lower right of the screen the word . AUTO> letters.
When the auto-adjustment is completed the word AUTO> will disappear. The auto-adjustment of the white level is cancelled by input switching and signal mode change.
I
AUTO
1
* When start up screen is displayed ("NO INPUT IS DETECTED" or "SYNC IS OUT OF RANGE" is displayed), SETUP menu items other than VOLUME cannot be set. TINT cannot be adjusted with PAL/SECAM video signal input. q TINT, COLOR and SHARPNESS cannot be adjusted with an RGB signal input. PHASE and H. SIZE cannot be adjusted with a VIDEO signal input. Auto-adjustment will take about 10 to 15 seconds to complete. In some cases auto-adjustment may not function normally, depending on the type of computer to which the unit is connected, and the signal sent. [. . . ] q Press the MENU button and select BRIGHT and press the@ button. q Remove the lens cap.
Only sound is heard without a picture Color is weak and tint is incorrect
Picture is dark
q Wiring the projector is not correct.
The color and tint have been adjusted Adjust the color and tint correctly. q The brightness and contrast has been
adjusted incorrectly. q The lamp has not been
q Adjust the brightness and contrast correctly. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE HITACHI CPX940E
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HITACHI CPX940E will begin.