User manual HITACHI CV80DP

[. . . ] To help secure the cord during use, fix it on the upper cord storage hook 6 . Fig. 4 6 5 HANDLE POSITION To change the position of the handle, first press with foot on the handle release pedal at the rear of the cleaner, and then lower the handle. (A) Upright position: When the handle is in this position the rotary brush is automatically raised away from the floor. (B) Normal working position: This position allows you to raise the front of the nozzle head to clear steps. [. . . ] Open the bag compartment lid by pulling the bag compartment clamp as shown in Fig18. To remove the dust bag 22 supported by the bag holder, push down the top end 23 of the bag holder, then pull it out carefully. 23 22 Fig. Insert the bottom of the cardboard collar 24 into the collar support 25 of the dust receptacle, and push the top edge until it catches behind the lug 26 of the bag holder. To replace the bag compartment lid, first insert the projection of the lid into the groove on the cleaner and push into place. Make sure you always have available spare paper bags. The HITACHI PAPER BAG has been made especially for your cleaner. Paper bags may be purchased from your local dealer or from a HITACHI service center. In the event that replacement bags(or drive belts) are not available at your local shops, for where to buy please contact 01628 643000. NOTE:To avoid using the cleaner without the paper bag, the clamp system of your cleaner prevents the bag compartment lid from being clamped when the paper bag has not been replaced, or has not been set properly in place. NOTE:Put the bottom end of the paper bag into the bottom of the bag compartment so that the bottom end of the paper bag could not be caught between the bag compartment lid and the cleaner. 24 26 25 24 25 Fig. 22 -6- CARE OF AIR FILTERS MOTOR PROTECTION AIR FILTER(Fig. 22) Once or twice a year, or when it becomes visibly soiled, the motor protection air filter 27 may need cleaning. Remove the filter from the bottom of the bag compartment as shown in Fig. After washing the filter, dry thoroughly away from direct sun-light and fit it back into the cleaner. NOTE: If the air filter is used when wet, suction is impaired and the motor may be damaged. 27 Fig. 23 28 AIR FILTER (for CV-80D) HYGIENIC AIR FILTER (for CV-80DC)(Fig. 24, 25) Your vacuum cleaner has a highly efficient electrostatic exhaust air filter 29 to trap even the finest dust particles in the exhaust air. Once or twice a year, when the filter gets dirty, change the filter as follows. Hygienic air filters may be purchased from your local dealer. In the event that replacement filters are not available at your local shops, for where to buy please contact 01628 643000. Fig. 24 HEPA CLEAN FILTER (for CV-80DP)(Fig. 24, 26) Your vacuum cleaner has a highly efficient electrostatic exhaust air filter 30 to trap even the finest dust particles in the exhaust air. [. . . ] If there is no alternative to cutting off the mains plug, ensure that you dispose of it immediately, having first removed the fuse, to avoid a possible shock hazard by inadvertent connection to the mains supply. IMPORTANT The wires in the mains lead are coloured in accordance with the following code: Blue=Neutral, Brown=Live As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED. On no account connect either of these wires to the terminal marked E or by the earth symbol or coloured green or green and yellow. THIS PRODUCT CONFORMS WITH THE PROTECTION REQUIREMENTS OF COUNCIL DIRECTIVES 89/336/EEC, 92/31/EEC, AND 93/68/EEC RELATING TO ELECTROMAGNETIC COMPATIBILITY. 3-J1861-3 Hitachi, Ltd. Tokyo, Japan International Sales Division THE HITACHI ATAGO BUILDING, No. [. . . ]