User manual HITACHI D13VG

[. . . ] Do not use any adapter plugs with earthed (grounded) power tools. unmodified plugs and matching outlets will reduce risk of electric shock. B) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. [. . . ] pRECAUTION Keep children and infirm persons away. When not in use, tools should be stored out of reach of children and infirm persons. Hold the drill and side handle securely with both hands when using. Do not wear gloves made of stuff liable to roll up such as cotton, wool, cloth or string, etc. Prior to drilling into walls, ceilings or floors, ensure there are no electric cables or conduits inside. Exposure to noise can cause hearing loss. Use auxiliary handles supplied with the tool. Model Voltage (by areas)* Power input No load speed Drill chuck capacity Steel Capacity Wood Twist Bit Hole Saw Flat Spade Bit Auger Bit Hole Saw D10VG D13VF D13VG (110V, 220V, 230V, 240V) 710W* 0­3, 000min­1 0­1, 200min­1 0­850min­1 0­600min­1 10 mm 13 mm 10 mm 10 mm 13 mm 13 mm ­ 38 mm 51 mm 70 mm 25 mm 32 mm 40 mm 40 mm ­ ­ 32 mm 38 mm 29 mm 70 mm 102 mm 114 mm 1. *Be sure to check the nameplate on product as it is subject to change by areas. <Capacity with Angle attachment (Optional accessory for D13VF and D13VG)> Model Speed of angle unit Steel Capacity Wood Twist Bit Hole Saw Flat Spade Bit Auger Bit Hole Saw D13VF D13VG LOW(650min­1) HIGH(1350min­1) LOW(400min­1) HIGH(900min­1) 13 mm 13 mm 13 mm 13 mm 64 mm 32 mm 70 mm 51 mm 40 mm 32 mm 40 mm 40 mm 38 mm 29 mm 38 mm 32 mm 114 mm 64 mm 114 mm 102 mm 1 Standard accessories are subject to change without notice. <D13VF and D13VG> (1) Hook (A) (2) Angle attachment Optional accessories are subject to change without notice. Power source Ensure that the power source to be utilized conforms to the power requirements specified on the product nameplate. Power switch Ensure that the power switch is in the OFF position. If the plug is connected to a receptacle while the power switch is in the ON position, the power tool will start operating immediately, inviting serious accident. Extension cord When the work area is removed from the power source. use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as practicable. When boring wood Use ordinary woodworking drill bits. (2) Place the chuck wrench in each of the three holes in the chuck, and turn it in the clockwise direction (viewed from the front side). (3) To remove the bit, place the chuck wrench into one of the holes in the chuck and turn it in the counterclockwise direction. To open the chuck jaws, hold the ring while turning the sleeve in the counterclockwise direction (viewed from the front side). (4) If it is hard to loosen the sleeve, fix the spindle using the open-end wrench, hold the sleeve firmly, and turn it in the loosening direction (counterclockwise when viewed from the front). [. . . ] Used D: Remarks CAUTION Repair, modification and inspection of Hitachi Power Tools must be carried out by an Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed. MODIFICATION Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements. [. . . ]