User manual HITACHI DK23DA SERIES QUICK INSTALLATION GUIDE
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HITACHI DK23DA SERIES. We hope that this HITACHI DK23DA SERIES user guide will be useful to you.
Lastmanuals help download the user guide HITACHI DK23DA SERIES.
You may also download the following manuals related to this product:
HITACHI DK23DA SERIES DATASHEET (165 ko)
Manual abstract: user guide HITACHI DK23DA SERIESQUICK INSTALLATION GUIDE
Detailed instructions for use are in the User's Guide.
[. . . ] 2. 5 inch Hard Disk Drives ATA/IDE
Quick Installation Guide
DK237A -21, DK237A-32, DK238A-32, DK238A-43, DK239A-48, DK239A-65, DK23AA-60, DK23AA-90, DK23AA-12, DK23BA, DK23CA -xx, DK23DA-xx and later
Setting the Jumpers 1. In a one drive system configure the new drive as a Master with no jumpers attached. [. . . ] Before handling the drive, touch an unpainted metal surface for a few seconds to drain any static electricity from your body. Keep the original packaging and static-protective bag in case the drive has to be returned.
If all of pins A, B, D are open, the drive is DRIVE 0(or Master).
2) DRIVE 1 (or Slave)
43 5 31 O--------OOO O--------OOO CA OO OO DB
ü correct
Quick Installation Procedure
X
incorrect
44
642
If jumper Position A-B is used, the drive is DRIVE 1 (or Slave).
3) CSEL Selection
43 5 31 CA OO OO DB O--------OOO O--------OOO 44 6 42
It is advisable to backup all data before proceeding with the installation. If your system BIOS cannot handle large capacity drives (over 540MB, or 8. 4GB) you may need to use a disk overlay program such as Ontrack's Disk Manager software. Contact your Hitachi supplier or the local Hitachi office. Dimensions / Screw Locations Check that the dimensions and screw hole locations are correct for your system.
If jumper Position A-C is used, DRIVE 0 or DRIVE 1 setting is determined by the condition of CSEL signal (pin# 28).
Attaching the Drive 1. Turn off the computer, unplug the power cord and remove the notebook battery. Match pin 1 of the 44 pin cable, usually denoted by a red stripe, to pin 1 of the drive interface connector, shown above. Mount the drive securely using 4 M3 (metric) screws with a maximum screw length of 2. 5 mm. Reinstall the notebook battery, plug in the power cord and turn on the computer. The computer may detect a configuration change and prompt you to proceed to the Setup screen. If it does not, enter the Setup screen using the key selection. Refer to the onscreen instructions or the computer handbook. [. . . ] All product names and logos are trademarks of their respective owners. For sales information on Hitachi products: 1-800-HITACHI (1-800-448-2244) Web Site: http://www. hitachi. com/storage [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE HITACHI DK23DA SERIES
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HITACHI DK23DA SERIES will begin.
HITACHI DK23DA SERIES DATASHEET (165 ko)
