User manual HITACHI GD-2000

[. . . ] 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. For Germany / Für Deutschland Module dürfen nur an eine Sicherheits-Kleinspannungs-Versorgung(SELVKreise) nach EN609501/VDE 0805 angeschlossen werden. Die Trennung von Netzspannung muß durch einen Sicherheitstransformator geschehen. GD 2000 DVD ROM M l P GD-2000 Manual 6/18/98 5:22 PM Page 4 Labeling The equipment is classified as a Class 1 level laser product. This label is fixed to the bottom of the DVD-ROM Drive. Important Safeguards SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR EQUIPMENT 1. [. . . ] (See page 10) · Moving your DVD-ROM drive Remove the disc and close the disc tray before moving the DVD-ROM drive. If your DVD-ROM drive is moved with the disc loaded or the disc tray opened, both the disc and the DVD-ROM drive may be damaged. Precautions For Care · Cleaning of the DVD-ROM drive, discs · Never clean your DVD-ROM drive and discs with silicon cloths or cloths soaked in water, solvents (thinner, benzine), abrasive cleaner, anti-static sprays, any record cleaner sprays, liquid cleaner or aerosol cleaner. It may damage or discolor the coating of the DVD-ROM drive and damage or deform discs. · Clean your DVD-ROM drive including the disc tray and discs with a clean, dry, soft cloth at least once a month. · Cleaning of disc If you begin to get error messages that your drive is unable to read a disc, it may mean that cleaning is needed. · Eject the disc and visually inspect the disc for scratches. If there are scratches on the surface of the disc, change the disc. · Eject the disc and clean as follows: 1. Clean the disc with a clean, dry, soft cloth. Clean your DVD-ROM drive's pick-up lens using a cleaning disc. GD 2000 DVD ROM Manual Page GD-2000 Manual 6/18/98 5:24 PM Page 8 Controls and Functions 6 7 Front Rear 34 12 5 89 10 11 1) DVD INDICATOR Indicator lights green when DVD-ROM media is detected in the drive. 2) LOADING/UNLOADING/BUSY INDICATOR Indicator blinks amber only when the disc tray is being opened or closed, or when the DVD-ROM drive is accessing data. 3) HEADPHONE JACK ( 3. 5 mm) 4) HEADPHONE VOLUME CONTROL Adjust the headphone volume. 5) OPEN/CLOSE BUTTON Press this button to open or close the disc tray. 6) DISC TRAY When the power of the DVD-ROM drive is turned off, the disc tray cannot be opened and closed. 7) MANUAL EMERGENCY EJECT HOLE Only in case of emergency. If the disc tray does not open when the OPEN/CLOSE button is pressed, the DVD-ROM drive's Manual Emergency Eject mechanism may be activated. This should be used only in case of an emergency. (See page 12 about Manual Emergency Eject Procedure) 8) AUDIO OUTPUT TERMINAL Circuit Board Rch GND Lch GD-2000 DVD-ROM Manual - Page GD-2000 Manual 6/18/98 5:25 PM Page 9 9) DEVICE CONFIGURATION JUMPER This connector is used to set operation modes such as Master, Slave and CSEL 642 Device is Master 531 or (default setting) Device is Slave Cable Select 10) ATAPI INTERFACE CONNECTOR ATAPI bus connection (40 pin) 11) POWER SUPPLY CONNECTOR (DC Input) For connecting the power supply cable. Circuit Board +5V GND +12V Installation Requirements HARDWARE · · · · · DVD-ROM drive Interface card Interface cable Power supply cable Mounting screws GD 2000 DVD ROM M l P GD-2000 Manual 6/18/98 5:25 PM Page 10 HARDWARE OPTION · Audio connecting cable · Sound card SOFTWARE · DVD-ROM device driver NOTE: If you need an interface card, interface cable or DVD-ROM device driver, contact your dealer. Hardware Installation To install this DVD-ROM drive in the host computer, refer to the instruction manual of each host computer. To install the interface card in the host computer, refer to the instruction manual of each host computer and each interface card. Install the DVD-ROM drive following the general installation procedure shown below: 1) Check the Device Configuration Jumper Settings of the DVD-ROM drive such as Master, Slave, CSEL. (See page 9) 2) Turn off the host computer and unplug the power supply cable of the host computer. 4) Install the DVD-ROM drive into the host computer and mount tightly with screws. [. . . ] If the disc tray still will not open, the DVD-ROM drive's Manual Emergency Eject Mechanism may still be activated. This should be used only in case of an emergency. GD-2000 DVD-ROM Manual - Page 12 GD-2000 Manual 6/18/98 5:26 PM Page 13 Removal Procedure 1. Turn off the DVD-ROM drive and wait at least 15 seconds until the disc stops rotating. Insert the Eject Bar (for example, a straightened paper clip) into the Manual Emergency Eject Hole about 25 mm (1 inch). [. . . ]