User manual HITACHI HM4721D

[. . . ] COLOR MONITOR HMm4721-D/ HM-4787-D USER'S MANUAL WARNING FCC NOTICE NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] FCC NOTICE To comply with FCC regulations, a shielded interface cable is required. WARNING NOTE REMOTE CONTROL VIDEO INPUTS c Fig. 2. 1 Rear View E-7 CHAPTER 3 OPERATION 3. 1 OPERATOR CONTROLS This chapter explains in detail how to operate the HM-4721-D/HM-4787-D monitor. At first, before you operate your monitor , turn on the rear main power switch of your monitor. (The position of the main power switch, see page E - 7. ) This section briefly describes the functions of the switches and controls. (1) Main Power switch Located on the rear panel of the monitor. Set to ' I ' to turn on the power, and the power indicator becomes green. If the monitor will not be used for a long time, turn off this switch. (2) Front Power switch When this switch is pressed while the Main Power switch is on and the power indicator is green, the indicator turns to orange and nothing is displayed on the screen. The stored data is recalled to display the initial screen when the power is turned on again after once turned off. If this button is pressed in adjustment mode, the mode is changed to normal operation mode and all indicators go out. c 5 lSELECT button When this button is pressed, the indicator lights up as follows: MODE 2 MODE 1 -7 ED Horizontal centering tL e Horizontal width tL lg Vertical centering t1 m Vertical height tL m Side pincushion f4 0 Rotation T 1 COLOR Color temperature fJ Press SELECT Holding down the SELECT button and button pressing the ADJUST (-1 button I Holding down the SELECT button and pressing the ADJUST (4 button Press SELECT button 6 ClADJUST button Functions as described in Table 3. 1 for each item selected with the SELECT button (the indicator lights up). Use the MODE selection switch to select MODE 1 or MODE 2. E-10 Horizontal Centering Setting 1. Select MODE 1 with the mode selection switch, and press the SELECT button until the H. Adjust the horizontal centering by pressing the ADJUST button (+) or (-1. / Horizontal Width Setting 1. Select MODE 1 with the mode selection switch, and press the SELECT button until the WIDTH indicator lights up. MODE 0 e i=J a 0 a SELECT 2. Adjust the horizontal width by pressing the ADJUST button (i) or (-1 . Vertical Centering Setting 1. Select MODE 1 with the mode selection switch, and press the SELECT button until the V. Adjust the vertical centering by pressing the ADJUST button (+) or C-1. ADJUST E-11 Vertical Height Setting 1. Select MODE 1 with the mode selection switch, and press the SELECT button until the HEIGHT indicator lights up. 2. Adjust the vertical height pressing the ADJUST button (+) or (-) . SPC Setting 1. Select MODE 1 with the mode selection switch, and press the SELECT button until the WC indicator lights up. 2. Adjust the side pincushion by pressing the ADJUST button (+) or (-) Rotation Setting 1. [. . . ] l Press the front power switch to interrupt the power save mode. l Check the contrast and brightness levels. E- 20 CHAPTER 4 SPECIFICATIONS 4. 1 SPECIF'ICATIONS dodel No. <esolution IRT (HM4721-D): (HM-4787-D): Size Active Display Area (max): (preset): HM-4721 -D HM-4721 -D/I-E&4787-D Up to 1600 x 1200/75Hz Up to 1600 x 1200/70Hz 21 inch FST (Flatter Screen Tube) +equency Interface AC Input Dimensions Weight 406 x 305 mm (15. 98 x 12. 00 inch) Typ. at 1600 x 1200 (preset): HM-4787-D 356 x 285 mm (14. 02 x 10. 63 inch) Typ. [. . . ]