User manual HITACHI PJTX10W

[. . . ] Projector PJTX10 PJTX10W/PJTX10E/PJTX10WAU User's Manual ­ Operating Guide Please read this user's manual thoroughly to ensure correct usage understanding. ENGLISH FRANÇAIS Manuel d'utilisation ­ Guide d'utilisation Nous vous recommandons de lire attentivement ce manuel pour bien assimiler le fonctionnement de l'appareil. DEUTSCH Bedienungsanleitung ­ Benutzerhandbuch Um zu gewährleisten, dass Sie die Bedienung des Geräts verstanden haben, lesen Sie dieses Handbuch bitte sorgfältig. Manual de usuario ­ Guía de funcionamiento Lea atentamente el manual de usuario del proyector para garantizar un uso adecuado del mismo. ESPAÑOL Manuale d'istruzioni ­ Guida operativa Vi preghiamo di leggere attentamente il manuale d'istruzioni per garantire una corretta comprensione delle istruzioni. ITALIANO TECHNICAL TECHNICAL Projector PJ-TX10 PJ-TX10W / PJ-TX10E / PJ-TX10W(AU) User 's Manual ­ Quick Guide Thank you for purchasing this projector. WARNING Before using, read the "User's Manual - Safety Guide" and these manuals to ensure correct usage through understanding. After reading, store them in a safe place for future reference. NOTE · The information in this manual is subject to change without notice. [. . . ] · This function may cause a certain degradation of the picture. In such a case, please select the TURN OFF. Display the Information: Pressing the or the ENTER button performs this function. · Use this function when you want the information about the current input (ex. the resolution and the vertical frequency at a COMPUTER input, the signal type of a video input) and setting states of the COMPONENT, the VIDEO and the FLAME LOCK. Select the S2-ASPECT Mode: TURN ON TURN OFF · This function performs only at a S-VIDEO input. · When the TURN ON is selected, an S2-Video signal can be identified and the optimum aspect ratio is automatically selected. · When the ASPECT button of the remote control is used or the ASPECT item of the MAIN menu is operated, the S2-ASPECT mode will be switched to the TURN OFF automatically. Reset the INPUT Menu Items: Selecting the EXECUTE performs this function. EXECUTE CANCEL · The items of the INPUT menu are collectively returned to the initial setting. Note that the INFORMATION item is not reset. VIDEO NR PROGRESSIVE INFORMATION S2-ASPECT RESET 27 Multifunctional Settings (continued) AUTO Menu With the AUTO menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. Item Description Automatically Adjust the Picture: Pressing the or the ENTER button performs this function. At a COMPUTER input: · V POSITION, H POSITION, H PHASE and HSIZE are automatically adjusted. Please use this function with the maximum window size. At a VIDEO input or S-VIDEO input: · This function performs only when the AUTO is selected under the VIDEO item of the INPUT menu. For a COMPONENT VIDEO input, although this function is ineffective, the signal type is identified automatically even if the AUTO is not selected. · This function automatically selects the optimum mode for the input signal. However, it may not work well at a PAL60 signal and some other signals. irregular picture, color lack), please use the function of VIDEO of the INPUT menu. · The operation of this function requires approximately 10 seconds. Also, please note that it may not function correctly with some input. Set the Automatically Power Off Timer: Long (Max. [. . . ] Run a command. 4 RS-232C Communication (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (`02H'+`00H'+ type (2 bytes)+`00H'+`00H') from the computer to the projector. (2) The projector returns the response code `1DH'+ data (2 bytes) to the computer. Changing the projector settings (Set command) (1) Send the setting code Header + Command data (`01H'+`00H'+ type (2 bytes) + setting code (2 bytes)) from the computer to the projector. (2) The projector changes the setting based on the above setting code. (3) The projector returns the response code `06H' to the computer. Using the projector default settings (Reset Command) (1) The computer sends the default setting code Header + Command data (`06H'+`00H'+ type (2 bytes) +`00H'+`00H') to the projector. [. . . ]