User manual HITACHI ULTRASTAR 9ZX QUICK INSTALLATION GUIDE

[. . . ] Sixty eight and eighty pin (Wide SCSI) devices both have 16 possible addresses 0-15). SCSI address bits 3, 2, 1, and 0 of the 32-pin Jumper Block are used to select the SCSI device ID. Reserved Auto Start Blank External Activity LED Write Protect GND SCSI Address Bit 3 2 1 0 Autostart Delay Reserved Disable Sync Negotiations Disable SCSI Parity Disable Unit Attention Disable Wide Negotiations 2. Do not apply any force to the drive during handling or installation. 1357 11 13 15 17 19 21 23 25 27 29 31 1 2 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 GND GND Reserved Reserved +5V GND Termination Power Enable 3. [. . . ] This procedure may require using a bootable System Diskette containing FDISK. COM and FORMAT. COM. Enable Active Termination Note: For attachment to a Macintosh, place jumpers on pins 29 & 30 to Disable Unit Attention and pins 11 & 12 for Auto Start. Power Pin 1 Aux Connector Pin 1 SCSI Pin 1 :::::: Pin 35 Pin 2 Page 1 IBM Hard Disk Drive Technical Support Center version 3. 0 IBM storage products Note In the table below, "off" means a jumper is not in place and "on" means a jumper is in place. Bit 3 off off off off off off off off on on on on on on on on Bit 2 off off off off on on on on off off off off on on on on Bit 1 off off on on off off on on off off on on off off on on Bit 0 off on off on off on off on off on off on off on off on Address 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Partitioning and formatting (with DOS 5. 0 or later) Caution: Be sure that you select the correct hard drive. Partitioning and formatting will erase all data. At the DOS prompt type FDISK, press [ENTER], and follow the instructions on the screen. To format the primary system drive, type FORMAT C:/S at the DOS command prompt and press [ENTER]. The /S parameter makes C: the operating system startup drive. To format a second drive (not C:), type FORMAT X: (where X is the drive letter assigned by FDISK) at the DOS prompt and press [ENTER]. Remove the diskette and restart your computer. If your system will not boot up after complete installation, recheck all settings. If the system still fails to boot up, remove the new drive to return the system to its original configuration and call the IBM Hard Disk Drive Technical Support Center. Attaching the drive 1. Turn off the computer, unplug the power cord and open the case. The DGVS drive requires Active Termination on both ends of the SCSI cable (the SCSI controller normally provides internal termination for one end of the cable). If the DGVS drive is the only device on the SCSI cable, attach it to the end of the cable furthest from the controller and enable termination by placing a jumper across pins 13 and 14 of the Option Jumper Block. If the drive is attached to a cable that contains other devices and the new drive is not attached to the end of the cable, the jumper across pins 13 and 14 must be removed and Active Termination must be supplied by the device at the end of the cable. Select the other option jumpers as required by your computer. Mount the drive securely, using the appropriate brackets or rails, in any axes, using four 6-32 UNC metric screws in the bottom or side mounting holes. The maximum screw insertion depth for mounting is 3. 8 mm (. 15 in). [. . . ] Ultrastar 9ZX Hardware/Functional Specification, version 2. 20 Ultrastar 18XP/9LP/9ZXParallel SCSI Disk Drive Logical Interface Specification, vers. 6. 0 Product Description data represents IBM's design objectives and is provided for comparative purposes; actual results may vary based on a variety of factors. This product data does not constitute a warranty. [. . . ]