User manual HITACHI UT32V502W

[. . . ] TM Hitachi UltraVision® HDTV Monitor 1. 5TM UltraThin LCD HDTV Monitor 32" Class (31. 51" Diagonal) Anthracite Pearl Crystal Frame(UT32V502) White Pearl Metallic Crystal Frame(UT32V502W) 1366 x 768p 120 Hz, PictureMasterTM V (1) HDMITM (V. 1. 3 with CEC) Input; (1) RGB D-sub15 Input with Audio Operating Guide UT32V502 UT32V502W Model Name Record the serial number of your monitor for future reference. SERIAL NO. This serial number is located on the back and right side of the monitor. If you have a question about this product please call 800-Hitachi for assistance READ THE ENCLOSED INSTRUCTIONS CAREFULLY. KEEP THIS OPERATING GUIDE FOR FUTURE REFERENCE. CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . 02 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The Indicating Lamp illuminates in Green, and the Illumination Lamp turns Blue. Once the Main Power switch is on, you can turn On/Off by pressing the Power (On/Off) button on the remote control. Main Power Switch (on the underside) Front To turn Off the power to the unit: 1. Press the Power (On/Off) button on the remote control. The Indicating Lamp turns Red (Standby mode), and the Illumination Lamp turns off. Press the Main Power switch on the unit to completely turn Off the power to the unit. NOTE Rear Power On/Off button While the Indicating Lamp illuminates in Red (Standby mode), you can turn On/Off by pressing the Power (On/Off) button on the remote control. The Indicating Lamp/Illumination Lamp Status Indicating Lamp Off Red Green Orange Blinking Green NOTE Illumination Lamp ­ ­ Blue ­ Blue Power Status Off Standby mode On Power Save mode On Refer to 42 Remark ­ ­ ­ and 43 for the condition. Receiving Remote Control signal If the image does not appear on the screen at all, or if there is any problem with it, see "TROUBLESHOOTING" on 43 ~ 45 . This may help you to solve the problems. After turning On, it takes about 6 seconds until the monitor starts up. Please note that buttons on the remote control and the unit (such as the Power button) do not work during this period of time. If power is interrupted during use of the unit, to avoid sudden surges of electricity when the power comes back on, turn off the main power to the unit before leaving home. BASIC OPERATION (continued) Volume Up/Down 1. To increase the sound volume, press the Volume Up button on the remote control or control panel. The Volume Indicator value on the screen will shift to the right. To decrease the sound volume, press the Volume Down button on the remote control or control panel. The Volume Indicator value on the screen will shift to the left. Volume Up/Down button Mute button Mute 1. To mute sounds, press the button on the remote control. The sound of the unit is temporarily turned Off. The color of the Volume Indicator will turn into grey while muting the volume. To turn the sound back on, press the button again, or press the Volume Up button on either the remote control or control panel. The color of the Volume Indicator will turn back to blue. NOTE Volume Up/Down button 20 You can decrease the volume by pressing the Volume Down button while the sound is muted. 23 BASIC OPERATION (continued) Menu button By pressing the Input Select button , you can switch the input to display the image outputting from the external equipment connected to each terminal (HDMI and RGB (/Composite)). <From Remote Control> Press the button on the remote control. Each time this button is pressed, the screen displays the corresponding mode in the following sequence. HDMI RGB (/Composite) Input Select button RGB Input Select button HDMI Input Select button Press the or button to directly select the input mode. <From Control panel> The Input modes can also be switched using the Input Select button on the control panel. Each time this button is pressed, the screen displays the corresponding mode in the following sequence. HDMI RGB (/Composite) Input Select NOTE Switching between RGB and Composite Mode When pressing button, you will see the image from either RGB or Composite mode. [. . . ] All right, title and interest in and to the Software and any intellectual property associated therewith, including any accompanying printed materials, shall belong to HITACHI and its licensors and suppliers. Except as expressly provided herein, neither HITACHI nor any of its licensors or suppliers grants to you under this Agreement any express or implied right in or to any patents, copyrights, trademarks, trade secrets or other intellectual property. All right, title and interest in and to the intellectual property rights associated with any content that is accessible through use of the Software shall belong to the applicable content owners and may be protected by copyright or other intellectual property laws and treaties. This Agreement grants you no rights to use such content. [. . . ]