User manual HITACHI UT47X902

[. . . ] TM Director's Series HDTV Monitors ® 1. 5" UltraThin Liquid Crystal Display Black Sapphire Crystal Frame 1920 x 1080p with High Efficiency EEFL Backlight (1) HDMITM (V. 1. 3 with CEC) Input; (1) RGB D-sub15 Input with Audio Operating Guide UT37X902 UT42X902 UT47X902 Model Name READ THE ENCLOSED INSTRUCTIONS CAREFULLY. KEEP THIS OPERATING GUIDE FOR FUTURE REFERENCE. Record the serial number of your monitor for future reference. SERIAL NO. This serial number is located on the back and right side of the monitor. ANY QUESTION ABOUT THIS PRODUCT PLEASE CONTACT 800-Hitachi CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . 02 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The remote will now control the desired device. Power button Device buttons Numeric buttons 4. 6. SETUP EXAMPLE (Hitachi Cable Box with precode 0003) 1. Select Cable mode by using your SAT/CBL button to position the LED indicator on SAT/CBL. Hold down the SAT/CBL button on the remote and press the numbers 0, 0, 0 and 3. The indicator light will flash 3 times if the code was accepted. Aim the remote at the cable box and press the POWER button. The remote will turn off your cable box when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your cable box. If the cable box does not turn off, try a different four digit preset code. The remote will now control your Cable box. Remote Control Backlight Feature When you press any remote control button, the buttons will light up. The illumination will light a few seconds during this time. The buttons will appear to light if the room is dark. 7. Repeat the same procedure for your set-top-box or satellite receiver (select SAT/CBL), your DVD (select DVD), your VCR/PVR(select VCR/PVR), or your AVR (select AVR). NOTE Disabling Remote Control Backlight Feature 1. While holding the TV mode key enter ASPECT, MUTE in sequence. To re-enable the backlight feature do steps 1~3 again (these steps toggle the Backlight Feature on and off, default is ON). If your external device cannot be operated after performing the above procedures, your external device code has not been precoded into the remote. In the unlikely event that your external device cannot be operated after performing the above procedures, please consult your external device operating guide. The remote control will remember the codes you have programmed even after the batteries are removed from the remote control. To reset all programmed codes to factory default place remote control in TV mode, then press and hold TV mode key and enter "9", "8", "1" in sequence. See page 30 Learning Setup on the Hitachi Remote Control to see if other device's Remote codes can be learned by this remote. 25 SETUP OPERATION (continued) ENGLISH 26 How to Use the Remote to Control your External Devices Cable Device Button Set-Top-Box/ Satellite Receiver Device Button MY CABLE BOX CODE IS:____________________ NOTE MY SET-TOP-BOX/SATELLITE RECEIVER CODE IS:____________________ NOTE Refer to the operating guide of the Cable Box for operation of the buttons exclusively for the Cable Box. PRECODED CABLE BOX buttons Refer to the operating guide of the Set-Top-Box/Satellite Receiver for operation of the buttons exclusively for the Set-Top-Box/Satellite Receiver. PRECODED SET-TOP-BOX/SATELLITE buttons These buttons transmit the chosen precoded STB/Satellite codes : -Power -Cursor & OK -Number PAD -Menu -Info -Enter -Return -Channel Up & Down -Fav CH -Guide -Dash(-) -Macro Keys -Last CH These buttons transmit the chosen precoded cable codes : -Power -Cursor & OK -Number PAD -Menu -Info -Enter -Return -Channel Up & Down -Fav CH -Guide -Dash(-) -Macro Keys -Last CH EXCLUSIVE TV mode (Monitor) buttons These buttons are for operating the TV : -Input -P. Mode -HDMI -Aspect -Vol Up & Down -RGB -Mute EXCLUSIVE TV mode (Monitor) buttons These buttons are for operating the TV : -Input -P. [. . . ] Except as expressly provided herein, neither HITACHI nor any of its licensors or suppliers grants to you under this Agreement any express or implied right in or to any patents, copyrights, trademarks, trade secrets or other intellectual property. All right, title and interest in and to the intellectual property rights associated with any content that is accessible through use of the Software shall belong to the applicable content owners and may be protected by copyright or other intellectual property laws and treaties. This Agreement grants you no rights to use such content. Any rights of HITACHI not expressly granted to you hereunder are reserved expressly by Hitachi. [. . . ]