User manual HITACHI VM-1600A

[. . . ] TABLE OF CONTENTS HITACHI Instruction Manual Video Camera/Recorder VM-1600A/VM-2600A 1 Hitachi Home Electronics (America), Inc. 3890 Steve Reynolds Blvd. , Norcross, GA 30093 Pointe Claire, Tel. 404-279-5600 HITACHI SALES CORPORATION OF HAWAII, INC. 3219 Koapaka Street, Honolulu, HI 96819 Tel. [. . . ] When the correct date appears, press "STOP" button. 6. Press "F. FWD" or "REW" button to select year, and then press "STOP" button. 7. Press "F. FWD" or "REW" button as many times as may be required to select the correct hour, and then press "STOP" button. Repeat step 7 to select minute and AM/PM. After setting AM or PM, press "STOP" button to change the display and start the internal clock. Press "DATE/TIME" button after setting the clock. The display will change as follows each time the button is pressed. 35 DATE/TIME SETTING NOTE: · See the next page for setting the second clock. · The date/time graphics will be recorded whenever they appear in the viewfinder. To correct date/time information after starting the date/time 1. Press and hold "DATE/TIME" button, and then press "STOP" button. Correct the incorrect digit by using "F. FWD", "REW" and "STOP" buttons. To correct date/time information during programming 1. Press "STOP" button repeatedly until the flashing cursor will be removed from the viewfinder. Follow steps 1 and 2 of "To correct date/time information after starting the date/time". To set the second clock (The first clock operates even if you do not set the second clock. ) Before setting Set the first clock first. The second clock cannot be set unless the first clock has been set. Example When you go abroad where there is a time difference of minus 5 hours: 1. Press the "DATE/TIME" button to display the second clock. 2. Select the month, day, year following the same steps as "To set the first clock". 3. Select the correct hour, and then press "STOP" button. Select AM/PM. NOTES: · The minutes of the second clock can not be set. they are the same as those of the first clock. · The first clock operates even while the second clock is being set. 5. After setting AM or PM, press "STOP" button to erase the flashing cursor. NOTES: · When the date or time of the first clock is flashing, you cannot delete the display. [. . . ] We expect that no maintenance other than head cleaning will be required during the warranty period of most users, unless the video camera/recorder is heavily used or seldom used. Normal maintenance is the responsibility of the user, although defective parts are covered during the warranty period. Consult your VCR service center to determine recommendations for normal maintenance based upon your location, use patterns and machine age. 90 SPECIFICATIONS SPECIFICATIONS General Power requirements Power consumption Dimensions: Weight Video Recorder Section Format Record/playback system Video signal Tape speed Video output Audio output Fast forward/rewind time 9. 6V DC 8 watts (nominal) 4-13/16"(W) x 7-13/16" (H) x 14-1/2" (D) 122(W) x 198(H) x 369(D) mm 4. 6 lbs (2. 1 kg) VHS Two video record/playback heads plus a flying erase head EIA standard NTSC color 33. 35 mm/sec. 1. 0 Vp-p, 75 ohm -7. 8 dBs (316 mVrms), less than 1 kohm Less than 6 minutes with T-120 cassette Camera Section Scanning 525 lines/ 60 fields/ 30 frames Required minimum illumination 1 lux (when "GAIN UP" is displayed in the viewfinder) Pickup device 1/3" CCD Lens diameter 37 mm 91 HOTLINE HOTLINE For U. S. A. [. . . ]