User manual HITACHI VTM410EUK

[. . . ] Should the fuse need to be replaced, an ASTA or BSI approved BS1362 fuse must be used of the same rating. If the fuse cover is detachable never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug. Fuse covers are available from your dealer. [. . . ] The OSD menu appears on the TV screen. C LOCK OK MENU Exit 3 " % # & !$ ' Cursor MENU R EV I EW No DATE CH T I ME V, P 117 / 5 TH 21 16 : 00~18 : 00 2 3 4 5 6 7 8 SELECT 0 MENU Exit Press one of the cursor buttons to select REVIEW, and then press the ENTER button. The TV screen will display the information you entered. Press the cursor or to view the next programme information immediately. 4 To clear a programme, press the button when the programme information you want to clear is displayed. One event's timer programme data is erased from the VCR's memory when the timer recording is finished, but daily and weekly programmes remain in the VCR's memory even after the timer recording is finished. · A programme without PDC signal will be deleted after it has been recorded. A programme with PDC signal will be automatically deleted after 04:00 in the morning following the day of recording. When you finish reviewing the programmes, press the MENU button to switch off the on-screen display. 5 Programme priority Example 1: When the programme start time is the same for more than one programme on the same day, they are recorded in the following order of Programme 1, 2, 3 . . . . 12. Programme 1 Programme 2 Programme 3 Programme 4 7:00 7:00 8:00 9:00 10:00 8:00 -- 8:00 Programme -- 9:00 Programme -- 10:00 Programme -- 11:00 Programme 9:00 1 2 3 4 10:00 11:00 Example 2: When the programmes overlap, the earlier programme has priority. Programme 1 Programme 2 Programme 3 Programme 4 7:00 7:00 9:00 10:00 11:00 8:00 9:00 -- 9:00 Programme 2 -- 10:00 Programme 1 -- 11:00 Programme 3 -- Programme 4 10:00 11:00 The actual programme recorded and the sequence is as shown in the shaded part of the diagram. 36 VIDEO LINK-RECORDING USING SATELLITE DECODER OR TV "VIDEO LINK" function allows you to easily prepare the VCR to record signals from a satellite/cable decoder or TV, without setting the timer programme. This avoids the necessity of doing timer programming twice. Controls VCR's Display Connect your decoder to L2 (the blue socket behind the VCR as shown in page 7). Controls TV Screen Tune your TV to the video programme number. 1 2 STOP PLAY/STILL REC /REW F. FWD/ 400x DRIVE TAPE NAVIGATION PROG TAPE NAVIGATION button Insert a cassette into VCR. The VCR will check the Tape Navigation signal. The TAPE NAVIGATION button will flash and " " will flash in the VCR display for about 10 seconds. · If a blank tape or a tape recorded on another VCR is inserted, you will need to store the tape data in memory, to activate Tape Navigation during playback. 3 REC 1 4 7 2 5 8 0 3 6 9 1 2 / 0 5 / 0 1 SA E240 0 : 30 1 0 : 2 0 SP 0000 4 Press the REC button to start recording. Notes: · Once you have selected the length of tape, it is not necessary to select it again for future recordings on the same tape. · The VCR recognises only programmes with recorded times of more than 5 minutes. · If you have selected an incorrect tape length, the correct data will not be stored in memory. 39 ADDITIONAL OPERATIONS S TOP 04 If you are using an E-30, E-60, E-120 or E-180 cassette, ignore the " " display. If you are using E-240, E-260 or E-300, press the 0000 button on remote control to select the type of tape you are going to use. The type of tape you have selected will display on the TV screen. Note: To properly store the tape in memory, you must select the type of tape you are going to use. (TAPE NAVIGATION) Tape Navigation Operation Controls TV Screen Cassette with Tape Navigation data Insert a cassette recorded on this VCR. The VCR will check the Tape Navigation data. The TAPE NAVIGATION button will flash for a few seconds, and then change to steady light if the VCR has recognised the tape. No 5 DATE TAP E NAV I P ROG 3 1 2 CH START M I N BLANK 1 9SP 1 1 : 0 0 2 0 LP 1 / 4 42 1 7 : 0 0 1 5SP 2 10 / 5 L1 1 5 : 1 5 3 0 LP 3 20 / 7 22 REMA I N 1 1 6SP SOAP 2 0 SP SELECT & / / 6 NAVI Exit Press the TAPE NAVIGATION button on the VCR or the NAVI button on the remote control. [. . . ] The RF channel data will appear on the VCR display. Press the PROG or button to change the RF channel to " ". To stop the RF output, press the STOP button on the VCR or on the remote control again. Press the PLAY/STILL button, the test pattern will disappear and the VCR will now come out of the standby mode into the operate mode. 8 REC STOP PLAY/STILL /REW F. FWD/ 400x DRIVE TAPE NAVIGATION PROG 9 LINK REC STOP PLAY /REW F. FW 400x DRIVE PROG You should now be able to playback a prerecorded cassette. [. . . ]