User manual HITACHI VTMX211A

[. . . ] TABLE OF CONTENTS Video Deck VT-MX211A Owner's Manual Your Complete Guide to Videocassette Viewing and Recording Using these quality features: Bilingual on-screen menu display selectable in English or Spanish Infrared remote control Real time tape counter 181 channel capability PLL frequency synthesizer tuner with direct station call Auto power on and off system Auto counter reset Auto rewind when the end of a tape is reached Direct Button Operation 2 Step Picture Search Operation Still Digital Auto Tracking (DTR) Auto Repeat Rental Play Mode Three different tape speeds (SP/LP/SLP) IRT (Instant Recording Timer) 1 Year, 7 events (including Daily and Weekly Timer Recording) Auto Return HITACHI HOME HITACHI SALES HITACHI (HSC) ELECTRONICS CORPORATION CANADA INC. 3890 Steve Reynolds Blvd. , 3219 Koapaka St. Pointe Claire, Quebec Norcross, Georgia 30093 Honolulu, HI 96819 H9R 1B1, CANADA Tel. 514-697-9150 QR13224 ©Hitachi, Ltd. [. . . ] (CH3 or 4) 3 Turn on the VCR Press the POWER button to turn on the VCR. 19 PRESET FOR USE 4 Select the VCR mode Press VCR/TV button so that "VCR" appears on the display 5 Select "ENGLISH" or "ESPANOL" Select "ENGLISH" or "ESPANOL=Spanish" using CH/SET Then, press SELECT or MENU button. or button. 6 Begin channel preset Press SELECT button once. The tuner scans and memorizes all the active channels in your area. (TV mode: from CH2/ CATV mode: from CH1) · The VCR distinguishes between standard TV channels and cable channels. 7 After scanning The tuner stops on the lowest memorized channel. The TV screen returns to TV mode. · If you subscribe to CABLE TV, "CATV" appears on the display. · If "TUNER SET UP" appears on the TV screen again, check the cable connections. The VCR will begin preset again. TO RECALL A DESIRED CHANNEL You can select the desired channel by using CH/SET pressing number buttons on the remote control. or button or directly Note for using number buttons: 20 PRESET FOR USE · When selecting cable channels which are higher than 100, press 100/ENT button first, then press the last two digits. (To select channel 125, first press "100/ENT" button then press "2" and "5"). · You must precede single-digit channel numbers with a zero (02, 03, 04 and so on). TO DELETE PRESET CHANNEL The channels you no longer receive or seldom watch can be deleted from the memory. (Of course, you can add the deleted channel into the memory again. ) NOTE: You must use the remote control for this procedure. Make sure. . . · Turn on the TV and set the TV channel to the same video output channel as located on the back of the VCR. (CH 3 or 4) · Press VCR/TV button on the remote control so that "VCR" appears on the display. 1 Select the main menu Press MENU button. The main menu appears on the TV screen. 2 Select "INITIALIZE" or button repeatedly to point to "INITIALIZE". Press CH/SET Then, press SELECT button. 3 Select "CHANNEL SET UP" or button repeatedly to point to "CHANNEL SET UP". Press CH/SET Then, press SELECT button. 21 PRESET FOR USE 4 Select "ADD/DELETE CH" Press CH/SET or button repeatedly to point to "ADD/DELETE CH". Press SELECT button. 5 Enter the desired channel number Press the number buttons or CH/SET or channel number appears. (Example: CH02) button repeatedly until your desired 6 Delete it from memory Press ADD/DELETE button so that "DELETE" flashes on the TV screen. To delete another channel, repeat steps [5] and [6]. If you press ADD/DELETE button again, the channel is memorized again. 7 Exit the preset mode Press MENU button to return to TV mode. NOTE: To confirm that channel(s) has been deleted or added, press CH/SET button. or 22 PRESET FOR USE CHANNEL PRESET AGAIN 1 Select the main menu Press MENU button. [. . . ] Check the corresponding POSSIBLE CAUSE and CORRECTIVE ACTION columns to remedy the problem. SYMPTOM NO POWER TO VCR POSSIBLE CAUSE POWER CORD IS NOT CONNECTED. VCR CLOCK IS NOT SET CORRECTLY THE ERASE PREVENTION TAB ON THE CASSETTE IS MISSING. THE TV AND OR VCR IS IN THE TV MODE. TIMER RECORDING IS NOT POSSIBLE. CORRECTIVE ACTION CONNECT POWER CORD TO AC OUTLET. PLACE A PLASTIC TAPE OVER THE HOLE. SET YOUR TV TO THE VCR MODE ANDO RO PRESS VCR/TV BUTTON ON THE REMOTE CONTROL SO THAT VCR APPEARS ON THE DISPLAY. FINE TUNE YOUR TV HEAD CLEANING IS NECESSARY CONSULT THE NEAREST HITACHI AUTHORIZED SERVICE CENTER. ` ADJUST TRACKING CONTROL CORRECTLY FOR A BETTER PICTURE. RECORDING MODE CANNOT BE ENGAGED. [. . . ]