User manual HOLMES HASF2018

[. . . ] Page1 · To disconnect, grip plug and pull from wall outlet. · Always use on a dry, level surface. · Do not operate without fan grills properly in place. · This product is intended for household use ONLY and not for commercial or industrial applications. WARNING: To reduce the risk of fire or electrical shock, DO NOT USE THIS FAN with any SOLID STATE Fan Speed Control Device PLEASE READ AND SAVE THESE INSTRUCTIONS THIS PRODUCT IS EQUIPPED WITH A POLARIZED A. C. [. . . ] STEP 3: Replace blade, tighten blade cap, and securely fasten the front grill. Fan Post Screw Screw Hole Fan Head, Base, and Pole Cleaning: Extension Pole Using a soft, moist cloth, with or without a mild, soap solution, carefully clean the fan base, pole, and head. Please use caution around the motor housing area. Do not allow the motor or other electrical components to be exposed to water. NOTE: If your fan does not have a screw hole in the extension pole but instead has an indentation around the top of the pole; please do the following: Place the fan head assembly onto the extension pole and tighten the fan post screw until a secure fit is obtained. FAN STORAGE: Your fan can be stored in the off-season either partially disassembled or assembled. It is important to keep it in a safe, dry location. · If stored disassembled, we recommend using the original (or appropriately sized) box. · If stored assembled or partially assembled, remember to protect the fan head from dust. The exclusive Holmes Products FanBonnet is available to protect your fan. (See attached mail order form for special offer or call 1-800-5-HOLMES) OPERATING INSTRUCTIONS: Step 1. Plug cord into any standard 120 volt AC outlet. Please make sure the Speed Control Switch is in the Off position. This switch is located on the top of the Fan Motor Housing. The speed is adjusted by turning the control switch to the desired setting, Off--High--Med--Low. The Oscillation Control Knob is located on the top of the Fan Motor Housing. To Stop Oscillation, Pull Knob Up. DETACH FROM INSTRUCTIONS AND MAIL IN THIS FORM ADJUSTMENT INSTRUCTIONS: Tilt Adjustment: Follow these instructions to tilt the Fan Head for upward angle air movement. Step 1: To change the tilting angle of the fan head, simply loosen the Tilt Adjustment Knob (see figure 3 on Page 2) Step 2: Move the fan head to the desired angle, then firmly tighten the knob to lock in place. For short term or seasonal storage of your Holmes fan EXTEND THE LIFE OF YOUR FAN Height Adjustment: Follow these instructions to adjust the height of the fan. Step 1: Turn the Base Collar (see figure 4) counter-clockwise to loosen pole. Step 2: Adjust the pole to the desired height, and firmly tighten the Base Collar in a clockwise direction. FAN BONNET $10. 99 PLUS SHIPPING AND HANDLING CLEANING/MAINTENANCE INSTRUCTIONS: Follow these instructions to correctly and safely care for your Holmes Products stand fan. Please remember: · Always unplug the fan before cleaning or disassembling. · Do not allow water to drip on or enter into the fan housing. · Be sure to use a soft cloth moistened with a mild soap solution. · Do not use any of the following as a cleaner: gasoline, thinner, or benzine. Fill out form on reverse side or call 1-800-5-HOLMES to place your order today. Page 3 FAN SERVICE INSTRUCTIONS: 1. Do NOT attempt to repair or adjust any electrical or mechanical functions on this unit. [. . . ] Holmes recommends you ship the package U. P. S. All shipping charges must be prepaid by you (as noted in paragraph E). Ship to: HOLMES PRODUCTS CORP. , CUSTOMER SERVICE DEPARTMENT, 233 FORTUNE BLVD. , MILFORD MA 01757 SHIPPING AND HANDLING CHARGES: $15. 00 This warranty gives you specific legal rights, and you may have other rights which vary from state to state. The provisions of this warranty are in addition to, and not a modification of, or subtraction from, the statutory warranties and other rights and remedies contained in any applicable legislation. [. . . ]