User manual HONEYWELL CT3611

[. . . ] PROGRAMMABLE THERMOSTAT OWNER'S GUIDE Seven Day Programmable Heat Pump Low Voltage (20 to 30 Vac) Thermostat and Wallplate Model CT3611 Para pedir estas instrucciones en español, llame al 1-800-468-1502. Pour obtenir ce ode demploi en français, composer le 1-800-468-1502. Honeywell CT3611 Table of Contents Step 1. Prepare for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remove Old Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Period Wake Default Setting Time (6:00AM) Heata (70°F/21°C) Coolb (78°F/25. 5°C) Leave Time (8:00AM) Heata (62°F/16. 5°C) Coolb (85°F/29. 5°C) Return Time (6:00PM) Heata (70°F/21°C) Coolb (78°F/25. 5°C) Sleep Time (10:00PM) Heata (62°F/16. 5°C) Coolb (82°F/28°C) a Your b Monday (Mon) Tuesday (Tue) Wednesday Thursday (Wed) (Thu) Friday (Fri) Saturday (Sat) Sunday (Sun) heating setpoints cannot be higher than 90°F (32°C) or lower than 40°F (4. 5°C). Your cooling setpoints cannot be higher than 99°F (35°C) or lower than 45°F (7°C). Program the First Day Start by programming the wake time and temperature for one day. q q q Press and release Press Day Wake . until the desired day displays. (Mon, Tue, Wed, Thu, Fri, Sat, Sun) or until the desired time shows in the display. 13 69-1081--3 Press time NOTE: q Press Program times are in 15 minute intervals. or until the desired wake temperature displays. The setpoint temperature range is 40°F to 90°F (7°C to 31°C) for heating and 45°F to 99°F (9°C to 37°C) for cooling. q Press Heat/Cool Settings to switch between setpoints. NOTE: q q q Press Press Program times are the same for heating and cooling. or Leave until the display shows the desired temperature setpoint. , Return or Sleep and repeat these steps for each program period. The first day is now programmed. Repeat each step in Program the First Day for the rest of the week. After the first day is programmed, you can copy that day to any other day using procedure in Copy a Day. Run Program NOTE: q Press when the entire week is programmed. Copy a Day Your thermostat can copy program settings from one day to another. q q q Press Press Press Wake , Leave , Return or Sleep to enter programming mode. Day until the display shows the day you want to copy. The display shows. Mon Copy M13327 q Press Day until the display shows the day you want to copy to. Mon Wed M13328 69-1081--3 14 q q Press Copy to accept the change. Repeat these steps for each day you want to copy. donE appears for two seconds and then the normal program display appears. M13329 NOTE: Clear a Program Period NOTE: q q q q q Press Press Wake cannot be cleared. Leave , Return , or Sleep for the program period you want to clear. Day until the desired day displays. Leave Press and hold the , Return , or Sleep for approximately 3 seconds until the time and temperature clear. Repeat the above steps for each period to be cleared. OPERATING YOUR THERMOSTAT Change Temperature Setting Until the Next Program Period (Temporary Change) q Press or until the screen shows the desired temperature setting. NOTE: The temporary temperature setting is displayed for about 3 seconds and then the room temperature is displayed. The setting cancels when the next program period starts or when you press Run Program . 15 69-1081--3 Change Temperature Setting Indefinitely (Hold) q q q Move the System switch to the desired position (Heat or Cool). Press Hold Temp then or to change your setting if desired. (The display changes from showing the setpoint temperature to room temperature after approximately three seconds). To cancel "Hold" press Run Program . Change the Temperature Setting Until a Designated Day and Period (Vacation Hold) q q q q Press Press Hold Temp twice. until the display shows the desired temperature setpoint. until the desired number of days that you will be away (1 through 255) is displayed. [. . . ] technology by selecting Conventional Recovery. Honeywell does not recommend this because the auxiliary heat comes on once the program time begins and run continuously until the setpoint is reached. Customize Your Thermostat. AM Room Mon Wake System Heat TEMPERATURE AM Room Mon Sleep Heat In Recovery System Heat AM Room Mon Sleep Heat In Recovery System Heat AM Room Mon Sleep System Heat 69-1081--3 20 WIRING DIAGRAMS See Table 1 on page 8 for additional wiring assistance. THERMOSTAT BL C BL C THERMOSTAT R W2 E W1Y O G R W2 E W1Y O G 2 EQUIPMENT MONITOR AUX. RELAY 2 HEAT CHANGEOVER VALVE 1ST STAGE HEAT RELAY 1 L2 L1 (HOT) 1 POWER SUPPLY. [. . . ]