User manual HONEYWELL EXCEL 12 FCU PLUS 4 LIGHTS DATASHEET

[. . . ] Registered Trademark Copyright © 2009 Honeywell Inc. · All Rights Reserved EN0B-0480GE51 R0909 EXCEL 12: FCU + 4 LIGHTS APPLICATION The Excel 12 FCU + 4 Lights application supports two HVAC sequences (HEAT, COOL, or CHANGEOVER), free inputs, 1 free binary output, and up to four lights. The application is delivered together with the plug-in and must be downloaded into the Excel 12 controller's flash memory during start-up. The user can customize the application using Honeywell's LNSTM plug-in with CARE or any LNSTM tool (e. g. [. . . ] Depending upon the actual occupancy sensor state, the effective mode will be either "occupied" or "standby. " Wall Modules: LONWORKS® wall modules Hardwired wall modules (e. g. T7460, T7560) Wireless wall modules (e. g. W7070+T7270 or RT7070) Master / Slave Functionality: The master / slave functionality allows easy adaptation to changed room usage. nviEnergyHoldOff SEQUENCE 0, POSITION *1 SEQUENCE 1, POSITION *1 nviLampValue master Excel 12 nvoLampValue nviLampValue slave Excel 12 nvoLampValue LIGHT LIGHT nvoLampValue THIS NV ALWAYS BINDS THE MASTER XL12 TO THE FINAL SLAVE XL12. slave Excel 12 nviLampValue LIGHT Fig. All lights switched on via any pushbutton NOTE: This binding shall not be used for applications involving dimming or constant light control. Binding via LONWORKS results in a short delay between the switching of the different lamps. Pressing the pushbutton repeatedly and rapidly may cause toggle effects. Benefits of Integrated Room Control The Excel 12 functionality provides you with a number of significant advantages: slave Excel 12 nvoEnergyHoldOff master Excel 12 FANSPEED, POSITION *2 OCCUPANCY MODE HEATING/COOLING POSITION *3 WINDOW CONTACT WINDOW CONTACT Considerable Reduction in Energy Consumption: · 25. . . 75% savings on electrical energy consumption for illumination. · Decreased heat generated by electric lights, thus reducing cooling energy requirements. Increased Convenience: · Occupancy sensor switches the light ON/OFF automatically. · Constant light control always provides the correct lighting. · Wireless control via ZAPP (see ZAPP System Engineering, EN0B-0286GE51). Increased Flexibility: · Flexible room usage if a LONWORKS® wall module or ZAPP (wireless remote control) is used. Reduced Engineering Effort / Expenses: · Just one LONWORKS® node (instead of two) is required to cover HVAC and Light. + reduced engineering and installation effort (e. g. wiring, binding, commissioning, etc. ) + reduced integration effort + lower cost due to reduced number of LNSTM credits + lower hardware total loop costs *1: ONLY IF SEQUENCE IS CONFIGURED *2: ONLY IF FAN IS CONFIGURED *3: ONLY IF CHANGEOVER SEQUENCE IS CONFIGURED MASTER nvoSequence [0] nvoSequence [1] nvoFanSpeed nvoEffectOcc nvoHeatCool SLAVE nviSequence [0] nviSequence [1] nvoFanSpeedCmd nviOccManCmd nviApplicMode nvoEnergyHoldOff slave Excel 12 nviEnergyHoldOff THIS NV ALWAYS BINDS THE MASTER XL12 TO THE FINAL SLAVE XL12. WINDOW CONTACT Fig. Master / Slave functionality master Excel 12 nvoLampValue nviLampValue slave Excel 12 LIGHT nviLampValue slave Excel 12 Fig. All lights switched via master pushbutton NOTE: Binding via LONWORKS results in a short delay between the switching of the different lamps. INTEROPERABILITY The Excel 12 has been certified as per LONMARK® Application Layer Guidelines V 3. 3. and is thus interoperable with all other devices in open LONWORKS® networks (including thirdparty devices). 3 EN0B-0480GE51 R0909 EXCEL 12: FCU + 4 LIGHTS Device Configuration The controller is configured using Honeywell's LNSTM plug-in. The plug-in can be started from CARE 4. 0 or any LNSTM tool (e. g. LonMaker for WindowsTM). Analog Input Object LonMark Analog Input Object (profile # 0520) mandatory Network Variables Configuration Parameter Value File LONMARK® Objects Network Variables The Excel 12 supports the following LONMARK® objects: one occupancy sensor object (#1060) (see Fig. 5) one open loop sensor object (#3) (see Fig. 10) one open loop actuator object (see Fig. 10) one space comfort controller object (see Fig. [. . . ] NV's associated with Lamp Actuator Object (profile #3040) name nviLampValue[4] nvoLampValueFb[4] type SNVT_switch SNVT_switch heartbeat no no Fig. Lonworks® connection / termination module 7 EN0B-0480GE51 R0909 EXCEL 12: FCU + 4 LIGHTS Table 7. NV's associated with Occupancy Sensor Object (profile #1060) name nvoOccSensor type SNVT_occupancy heartbeat yes Table 10. NV's associated with Space Comfort Controller FCU Object (profile # 8051) name nviSpaceTemp nviSetPoint nviSetptOffset nviOccSchedule nviOccManCmd nviOccSensor nviApplicMode nviFanSpeedCmd nviEnergyHoldOff nviSequence[2] nvoSequence[2] nvoSpaceTemp nvoUnitStatus nvoEffectOcc nvoHeatCool nvoFanSpeed nvoEnergyHoldOff type SNVT_temp_p SNVT_temp_p SNVT_temp_p SNVT_tod_event SNVT_occupancy SNVT_occupancy SNVT_hvac_mode SNVT_switch SNVT_switch SNVT_lev_percent SNVT_lev_percent SNVT_temp_p SNVT_hvac_status SNVT_occupancy SNVT_hvac_mode SNVT_switch SNVT_switch heartbeat yes no yes yes no yes yes no yes yes yes yes yes no yes yes yes Table 8. [. . . ]