User manual HONEYWELL HC60NG

[. . . ] The room unit HCW 80 is used for intelligent room temperature control in combination with the relay module HC60NG. It can be used to control gas and oil boilers, a variety of valves and actuators or electrical heating systems. no wiring to the room unit HCW 80 is required. Because of the simple HCW 80 analogue user interface with absolute set point temperature scale, the room set point temperature can be easily adjusted. [. . . ] The batteries have to be replaced when the red LED at the room unit HCW 80 flashes (see section 9 "Changing batteries"). Place the housing cover in position above and snap it down (see Fig. When selecting the operating site of each device ensure that the distance to radio devices such as radio headphones, cordless phones, etc. According to the DECT standard amounts to at least 1 m. Do not install the devices over metallic wall connecting sockets and at least 30 cm away from the cover of the heat generator. Correct the installation site of the room unit HCW 80 if necessary. The room unit HCW 80 can send a test signal to the assigned relay module HC60NG in order to test the signal strength. Keep the teach-in button of the HCW 80 pressed for at least 15 sec until the red LED of the HCW 80 is OFF. The HCW 80 is now in test mode and sends a test signal every 5 sec. When the RF communication is lost for a period of 1 h, the red LED of the relay module HC60NG is ON to indicate that no RF messages have been received during the last hour. When RF communication is re-established the relay module HC60NG will automatically return to normal operation mode. The teach-in operation is required if the relay module HC60NG and the room unit HCW 80 are not pre-bound e. Keep the button of the HC60NG pressed for at least 15 sec. the resetting was successful when the red LED flashes rapidly (1/9 ON/OFF). After the factory reset the HC60NG looses the communication with the HCW 80. After the power up of the relay module HC60NG the red LED will start to flash at 0. If this is not the case set the HC60NG into the reset mode see section 7 "Factory reset of relay module HC60NG". The room set point temperature can be set easily at the set point adjuster by means of an adjustment dial. The room set point range is from 10 °C to 30 °C including the frost protection setting (5 °C). The HCW 80 simulates a mechanical thermostat by LED indication as follows: The red LED at the HCW 80 will be switched ON for 4 sec if the deviation between the set point and the room temperature is >1 °C. [. . . ] 1) RF binding method Factory pre-bound with the room unit HCW 80 (kit Y6630D1007 only) Environmental & Standard Operating temperature 0 to 40 °C when relay load <8 A 0 to 30 °C when relay load >8 A ­20 to 55 °C Shipping & storage temperature Humidity Humidity range 0 to 90 % rh, non-condensing IP class 30 Meeting the following EN 60730-1 (1995), EN 55014-1 standards (1997), EN 55014-2 (1996), ETSI EN 300 220-3 (2000), ETSI EN 301 489-3 (2000) Temperature of ball thrust hardness test for housing components 75 °C and for live parts such as, for example, terminals 125 °C · Electrical Receiver power supply Switch type Output rating Wire access (receiver only) 230 V AC (+10 %, ­15 %), 50 Hz SPDT potential free 24­230 V AC, 10 A resistive, 3 A inductive, 0. From the rear (wall box mounting), right an bottom Do not dispose of the unit with the usual domestic refuse. Honeywell nu accept nici o responsabilitate pentru orice pierdere sau daun datorat oricrei erori sau omisiuni care ar putea fi coninut din neatenie în aceast schem. Hereby declares that this device complies with the basic requirements and other relevant regulations of guideline 1999/5/EC. [. . . ]