User manual HONEYWELL HS 30

[. . . ] All work may only be carried out by authorized technical personnel. De-energize the corresponding fuse during all work on the module*. The switch module has a radio receiver whose function can be impaired by metallic objects and radio devices. When selecting the operation site ensure that there is sufficient distance to metallic objects such as metal cabinets and doors, concrete ceilings with iron lattices and radio devices such as radio headphones, etc. Danger! Caution! Laying cables Lengthen the cables so that they protrude at least 10 cm out of the distribution box. 4 Mounting Remove the housing cover from the module. Lever the contact covers out with a screwdriver. Insert all the cables through the openings in the housing bottom. Connecting loads and pushbuttons Both pushbuttons and switches can be connected to the switch module. [. . . ] The display* at the Hometronic Manager HOMETRONIC shows the standard display (example): WE 29. 10. 1999 11:15 No Lifestyle active LIVING 20. 0 C Press the Dial button. The cursor* flashes in the lowest line. HOMETRONIC WE 29. 10. 1999 11:15 No Lifestyle active LIVING 20. 0 C LIFESTYLE TIME PROGRAMS DISPLAY SETTINGS INSTALLATION DE-INSTALLATION FUNCTION EXTENSION SENSOR FUNCTION Turn the Dial button to the right until "Menu" is selected. The following text is displayed: Turn the Dial button to the left until "Settings" is selected. The following text is displayed: The Hometronic Manager is in the "Settings" submenu. 9 Teach-in Assigning device switch HS 30 to Hometronic Manager as a device In the following example a humidifier is assigned to the switch module. Change to the "Settings" submenu as described on Page 9. Turn the Dial button until "Installation" HEATING/COOLING is selected. DEVICES/LIGHT The following text is displayed: SENSOR Turn the Dial button to the left until the "Devices/Light" selected: Press the Dial button. submenu is HEATING/COOLING SHUTTERS DEVICES/LIGHT SENSOR MODULE-1 MODULE-2 HUMIDIFIER CEILING LIGHT The module names are displayed. Turn the Dial button to the left until the corresponding module selected, e. g. : "Humidifier". is MODULE-1 MODULE-2 HUMIDIFIER CEILING LIGHT 10 Teach-in Press the Dial button. An * appears after the "Humidifier" module. MODULE-1 MODULE-2 HUMIDIFIER CEILING LIGHT * Activate Teach-in mode at the socket switching module within four minutes (see Chapter "Activating the Teach-in mode at the switch module" on Page 8). If "Q" is displayed after a module name, this module has already been assigned to the Hometronic Manager. The process of assigning or changing module names is described in the operating instructions of the Hometronic Manager. Installing device switch HS 30 at Hometronic Manager as a collection relay of thermostat control Installation of the collection relay (HS 20 or HS 30) has no effect on the maximum number of devices at the Hometronic Manager HCM 200. Example: Installing device switch HS 30 as a collection relay. Activate Teach-in mode at the HS 30 as described on Page 8. Change to the "Settings" submenu as described on Page 9. 11 Teach-in Turn the Dial button until "Installation" is selected. The following text is displayed: Turn the Dial button to the left until HEATING/COOLING SHUTTERS DEVICES/LIGHT SENSOR SENSOR SETPOINT ADJUSTER ROOM CONTROL BOILER REQUEST SWITCHING MODULE ANTI-FREEZE SENSOR THERMOSTAT SWITCHING MODULE ANTI-FREEZE SENSOR THERMOSTAT SWITCHING MODULE ANTI-FREEZE SENSOR THERMOSTAT "Boiler request" is selected. Press the Dial button. The following text is displayed: Turn the Dial button to the left until "Thermostat" is selected. Press the Dial button. An "*" appears after the "Thermostat" entry. The device switch is assigned. * The socket switching module HS 30 is installed as a collection relay. 12 Teach-in Uninstalling collection relay Change to the "Settings" submenu (refer to Page 9). Turn the Dial button until "De- HEATING/COOLING SHUTTERS Installation" is selected. SENSOR The following text is displayed: Turn the Dial button to the left until "Boiler request" is selected. SENSOR SETPOINT ADJUSTER ROOM CONTROL BOILER REQUEST SWITCHING MODULE ANTI-FREEZE SENSOR THERMOSTAT SWITCHING MODULE ANTI-FREEZE SENSOR THERMOSTAT SWITCHING MODULE ANTI-FREEZE SENSOR THERMOSTAT * * * * Press the Dial button. The following text is displayed: Turn the Dial button to the left until "Thermostat" is selected. Press the Dial button. The "*" after the "Thermostat" entry disappears. The collection relay is uninstalled. 13 Teach-in Installing device switch HS 30 at Hometronic Manager for boiler request (HK 10) Installation of the collection relay (HS 20 or HS 30) has no effect on the maximum number of devices at the Hometronic Manager HCM 200. Connect the switch module to the cable of the boiler control (refer to Page 5). Activate the Teach-in at the switch module (refer to Page 8). Change to the "Installation" submenu at the Hometronic Manager (refer to Page 8). Turn the Dial button to the left until the "Boiler demand" menu item is selected. The following text is displayed: Press the Dial button. SHUTTERS DEVICES/LIGHT SENSOR BOILER DEMAND SWITCHING MODULE * ANTI-FREEZING SENSOR The following text is displayed: After the Teach-in has been completed, the switch module is used for the boiler demand. 14 Teach-in Successful Teach-in If Teach-in was successful, the LED at the switch module extinguishes. Failed Teach-in If the LED at the switch module lights green with short breaks, the Teach-in has failed. Improve the transfer, avoid disturbances or shieldings, for example, by: ­ Wireless headphones, garage door opener, remote controls, metal parts ­ If possible, change the position of the switch module. [. . . ] All the assigned areas are controlled by means of time programs. Boiler demand Signal that the Hometronic Manager sends to the heating boiler when the setpoint drops below the minimum value. Connected load Intake power of the plugged-in device. Load Device which is connected to the Hometronic component (e. g. [. . . ]