User manual HONEYWELL RT7070A2008

[. . . ] HONEYWELL EXCEL 5000 OPEN SYSTEM RT7070A2008 ZAPP Wireless Handheld Operating Instructions Copyright © 2007 Honeywell Inc. All Rights Reserved EN1B-0399GE51 R1207A This page left intentionally blank. Overview Overview For your information Technical terms are explained in the glossary (page 14). [. . . ] Do not attempt to teach-in both an RT7070A2008 and a T7270B2009 to the same room. 3 EN1B-0399GE51 R1207A Adjusting Functions Adjusting Functions Activation Buttons The activation buttons are used to choose the following functions: occupancy override* setpoint offset* (temperature) fanspeed sunblinds light switchgear* or second light A B officestyle* A officestyle* B Control Buttons You can adjust the functions using the control buttons , , and OK. EN1B-0399GE51 R1207A 4 Adjusting Functions After pressing an activation button, you have 15 seconds to start adjusting the function with the control buttons. Occupancy Override* Setting to unoccupied Press . The occupancy override is set to 'unoccupied'. The occupancy override is set to 'bypass' (which means 'occupied' on the XL10 side) for a limited time. Press Setting to automatic operation . The occupancy override is set to 'automatic operation'. Press 5 EN1B-0399GE51 R1207A Adjusting Functions Temperature Setpoint Offset* If you press the or control button briefly, you lower or raise the temperature setpoint offset* in steps of 0. 5 °C. If you press it for longer, you lower or raise the temperature setpoint offset* by a maximum of 5 °C. Lowering Press . Press . The temperature setpoint offset* is lowered. Raising Press . Press . The temperature setpoint offset* is raised. Resetting Press Press OK. The temperature setpoint offset* is set to zero. EN1B-0399GE51 R1207A 6 Adjusting Functions Fanspeed If you press the or control button briefly, you lower or raise the fanspeed to a setting of "off", "one", "two", or "three". If you press it for longer, you lower or raise the fanspeed to the maximum value ("off" or "three"). Lowering Press . Press . The fanspeed is lowered. Raising Press Press . . The fanspeed is raised. Setting to Automatic Operation Press . Press OK. The fanspeed is set to 'automatic operation'. 7 EN1B-0399GE51 R1207A Adjusting Functions Sunblind If you press the or control button briefly, you automatically lower or lift the sunblind completely. If you press it for longer, you lower or lift the sunblind for as long as the button is pressed. It stops when you release the button. Lowering Press . Press . The sunblind is lowered. Lifting Press Press . . The sunblind is lifted. Stopping Press . Press OK. The sunblind is stopped. EN1B-0399GE51 R1207A 8 Adjusting Functions Light With the upper activation button , you can control the light. Switching Off Press Press . . The light is switched off. Switching On Press Press . . The light is switched on. Dimming Press . Press OK. The light is dimmed as long as you press OK. 9 EN1B-0399GE51 R1207A Adjusting Functions Second Light or Switchgear* With the lower activation button switchgear*. , you can control a light or Switching Off Press Press . . The light or switchgear* is switched off. Switching On Press Press . . The light or switchgear* is switched on. Adjusting Continuously Press . Press OK. The light or switchgear* is continuously adjusted as long as you press OK. EN1B-0399GE51 R1207A 10 Adjusting Functions Officestyle* Defining the Settings Adjust sunblinds, fanspeed, lights, etc. Press OK for at least five seconds. The officestyle* is defined. Activating the Defined Settings Press A or press B. Press OK briefly. The officestyle* is active. NOTE: The position of the sunblinds cannot be stored; rather, only sunblind commands ('up', 'down', or 'stop') can be stored. 11 EN1B-0399GE51 R1207A Child-Proof Lock Child-Proof Lock Locking Press any activation button and observe the LED*. If the LED* lights up green, the child-proof lock is not active. Simultaneously press the buttons , , and OK. The child-proof lock is now active. To test the child-proof lock, press any button. If the LED* flashes red, the buttons are locked. Unlocking Press any button and observe the LED*. If the LED* flashes red, the child-proof lock is active. Simultaneously press the buttons , , and OK. The child-proof lock is now deactivated. To test the child-proof lock, press any activation button. If the LED* lights up green, the buttons are unlocked. Removing the batteries deactivates the child-proof lock. EN1B-0399GE51 R1207A 12 Batteries Batteries You should change both batteries and use only leak-proof batteries: Micro-batteries*: Alkaline LR03 (service life: roughly two years) Open compartment for batteries. Batteries may discharge. Attention Make sure that each battery is inserted in the correct direction (+/- polarity). Replace batteries. [. . . ] The declaration of conformity of the product can be requested from the manufacturer. countries: This product may only be used if operation in the 868 MHz frequency band is permissible. EN1B-0399GE51 R1207A [. . . ]