User manual HONEYWELL S10010

[. . . ] (20 Nm / 177 lb-in) (seal-less dampers; air frictiondependent). FEATURES · · · · · · Self-centering shaft adapter Removable access cover Mechanical end limits (non-adjustable) Rotation direction selectable by choice of mounting orientation Mountable in any orientation (IP54 only when mounted on a horizontal shaft with access cover below the shaft) Mechanical position indicator ® U. S. Registered Trademark Copyright © 2005 Honeywell Inc. · All rights reserved EN0B-0463GE51 R0505 SmartAct S10010, S20010 MODELS order number S10010 S10010-SW2 S20010 S20010-SW2 supply voltage 24 Vac / 24 Vdc end switches -2 -2 power consumption 14 VA (driving) / 5 VA (holding) 16 VA (driving) / 5 VA (holding) torque 10 Nm (88 lb-in) 20 Nm (177 lb-in) Product Identification System N = non-spring return S = spring return 10 = 10 Nm (88 lb-in) 20 = 20 Nm (177 lb-in) 010 = modulating + floating 24 = 24 V 230 = 230 V SmartAct S 2 0 2 3 0 X Fig. [. . . ] Internal end switch triggering points Mechanical Stroke Limit Reduction For applications requiring a span of less than 95°, a simple adjustment can be made. When the rotational mounting of the shaft coupling is changed, the actuator drives less than the full 95° stroke. The stroke is adjustable in 5° increments. Once adjusted, the actuator drives until the shaft coupling reaches the mechanical stop (part of the housing). The stop causes the motor to discontinue driving, and the shaft coupling drives no farther. When the actuator returns, it stops at the fail-safe position. To set the fail-safe position, proceed as follows: 1. Remove the retainer clip from the shaft coupling and set it aside for later use. Remove the shaft coupling from the actuator. Rotate the coupling to the desired fail-safe position, aligning it based on the stroke labeling. EXAMPLE: Setting the shaft coupling to an approx. fail-safe position of 35° (as indicated on the housing) limits the stroke to 60° (see Fig. 5). Releasing the Manual Positioning To release the manual positioning with no power present, proceed as follows: 1. Turn the key ¼ of a turn in the direction indicated on the cover. Remove the key without engaging the gear train lock pin. The spring will return the actuator to the failsafe position. NOTE: Once power is restored, the actuator will return to normal automated control. 95° 1 3 4. Install the shaft coupling at this position. [. . . ] MODULATING CONTROL S1 black 24 Vac~ 1 2 Function Switch Position* 2-10 VDC Modulating 10-2 VDC Modulating 0-10 VDC Modulating 10-0 VDC Modulating Floating, Forward Floating, Reverse 24 Vac~ 1 2 Function Switch Position* 2-10 VDC Modulating 10-2 VDC Modulating 0-10 VDC Modulating 10-0 VDC Modulating Floating, Forward Floating, Reverse S1 S2 S3 S4 S5 S6 S2 black S3 black S4 gray S5 gray S6 gray CW CCW 0. . . 10 Vdc TERMINAL STRIP 1 3 4 5 0(2). . . 10 Vdc Y 10. . . 0(2) Vdc 3 4 *Shown in factory setting 0(2). . . 10 Vdc U 10. . . 0(2) Vdc 5 *Shown in factory setting ! Connect via safety isolating transformer! FLOATING CONTROL Connect via safety isolating transformer!MODULATING CONTROL END SWITCHES NOTE: Internal end switches S1 and S4 must be connected to the same power source. 5 EN0B-0463GE51 R0505 SmartAct S10010, S20010 DIMENSIONS 100 50 50 64 (min. ) 76 (min. from shaft end) 40 156 247 6 75 76 (min. ) Fig. [. . . ]