User manual HONEYWELL T7270B2009

[. . . ] WIRELESS WALL MODULE HONEYWELL EXCEL 5000 OPEN SYSTEM INSTALLATION AND OPERATING INSTRUCTIONS T7270B2009 STANDARDS AND NORMS The ZAPP System complies with CE and EN 300 220-1 and EN 301 489-1. It is recommended that devices be kept at room temperature for at least 24 hours before applying power to allow any condensation resulting from low shipping/storage temperatures to evaporate. Use in Combination with Legacy Devices The T7270B2009 ZAPP Wireless Wall Module is suitable for use only with the W7070A2000 ZAPP Wireless Receiver. It cannot communicate with (but is likewise unaffected by) legacy devices (e. g. NOTE: Do not attempt to teach-in both an RT7070A2008 and a T7270B2009 to the same room. TECHNICAL DATA Batteries Frequency Fig. [. . . ] Cycling with the UP button results in the following sequence of displays: "crescent moon", then nothing, then "half-sun", then "full sun". Cycling with the DOWN button reverses the sequence. NOTE: The OCCUPANCY function can be disabled (see section "PA: Disable/Enable OCCUPANCY Function" on page 6). When cycling with the "F" button, this function and the corresponding display in the LCD sequence will then be unavailable to the user. Default Function The LIGHT function is the default function. Thus, the user can adjust the setting (i. e. After the LCD test is then automatically performed, the name of the current software version in the T7270B2009 (e. g. "1. 03") will appear in the LCD and a special LCD sequence "t 1", then "t 2" will be shown while the given teach command is being transmitted. Default Display and Default Function If there is no user action for more than 4 sec, the T7270B2009 will automatically revert to the default display and the default function. Default Display In the default display (see for example Fig. 2), the current room temperature (in °C or °F, as desired) with a resolution of one-tenth of a degree is shown in the LCD. Further, the temperature symbol ­ a stylized thermometer (" ") ­ is also shown. EN1B-0389GE51 R1207A 4 T7270B2009 WALL MODULE CONFIGURATION MODE By configuring the T7270B2009, the user can alter its functions / displays to better reflect the actual operating environment (e. g. the presence of a fan, the number of speed levels it has, the number of light groups, etc. ) in which it is used. To configure the T7270B2009, proceed as follows: 1. Press the "F" button and, while still pressing it, press the UP button (for at least 5 sec). RESULT: "P-:--" appears in the LCD, indicating that the T7270B2009 is now ready for configuration. Then press the "F" button again and, while still pressing it, rotate the setpoint wheel to the desired parameter (e. g. RESULT: The LCD cycles through the various different parameters (P1 through PB) together with their current configurations. Release the "F" button and rotate the setpoint wheel to select the parameter value (e. g. Confirm your selection by pressing the UP button. You may now continue configuring ­ or leave the configuration mode and permanently store your configurations by pressing the DOWN button. P4: Temperature Setpoint Offset Limits With this parameter, the user can configure the range over which the temperature setpoint offset can be adjusted. · The range can be widened/narrowed with the setpoint wheel in steps of 1 K. · The default configuration is -3. . . +3 K. P5: Sunblind Runtime With this parameter, the user can configure the time during which the sunblinds rise/descend. · The runtime has a range of 1. . . 99 s. [. . . ] PB and PC Currently used with special custom models, only. · PB: Sunblind Grouping (default: 1 sunblind group) · PC: Sunblind Short/Long Button Press 1. . . 60 sec (default: 99 = disabled) MOUNTING Mount the T7270B2009 on an inside wall approximately 54 in. (1. 3 m) from the floor (or as specified on the installation drawings) to allow exposure to the average zone temperature. Do not mount the T7270B2009 on an outside wall, on a wall containing water pipes, or near air ducts. [. . . ]