User manual HOTPOINT A6TG1F C

[. . . ] Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. [. . . ] The cooker is fitted with a safety chain to be fixed by means of a screw (not supplied with the cooker) to the wall behind the appliance, at the same height as the chain is attached to the appliance. Choose the screw and the screw anchor according to the type of material of the wall behind the appliance. If the head of the screw has a diameter smaller than 9mm, a washer should be used. Concrete wall requires the screw of at least 8mm of diameter, and 60mm of length. Ensure that the chain is fixed to the rear wall of the cooker and to the wall, as shown in figure, so that after installation it is tensioned and parallel to the ground level. 0 63 52 2x65 78 75 236 189 167 232 186 164 128 104 78 2x99 119 114 309 248 219 Tripple Ring (TC) Ov en Grill 130 - TECH NICAL DA TA S R TC A S S Oven Dime ns io ns Hx Wx D Vo lu me Us eful me asu remen ts relating to the oven co mpartm en t Vo ltage an d frequ ency 31x43, 5x43, 5 cm 58 l width 46 cm depth 42 cm height 8, 5 cm see data plate may be adapted for use with any type of gas shown on the data plate. 1275/2008(Stand-by/Off-mode) R A A6TG1F EX A6GG1F EX Bu rner s 13 Start-up and use GB Using the hob Lighting the burners For each BURNER knob there is a complete ring showing the strength of the flame for the relevant burner. To light one of the burners on the hob: 1. Bring a flame or gas lighter close to the burner. Press the BURNER knob and turn it in an anticlockwise direction so that it is pointing to the maximum flame setting . Adjust the intensity of the flame to the desired level by turning the BURNER knob in an anticlockwise direction. This may be the minimum setting , the maximum setting  or any position in between the two. If the appliance is fitted with an electronic lighting device*(D) (see figure), press the ignition button, marked with , then hold the the symbol BURNER knob down and turn it in an anticlockwise direction, towards the maximum flame D setting, until the burner is lit. The burner may be extinguished when the knob is released. If this occurs, repeat the operation, holding the knob down for a longer period of time. X Flame adjustment according to levels the burner flame intensity can be adjusted with the knob according to 6 power levels, from maximum to minimum with 4 intermediate positions: a click will indicate the change from one level to another when turning the knob. The system guarantees a more precise adjustment, allows to replicate the flame intensity and to identify easily the preferred level for different cooking operations. To identify the type of burner, please refer to the diagrams contained in the “Burner and nozzle specifications”. burner Fast (R) Semi Fast (S) Auxiliary (A) Triple Crown (TC) Cookware Diameter (cm) 24 - 26 16 - 20 10 - 14 24 - 26  !On the models supplied with a reducer shelf, remember that this should be used only for the auxiliary burner when you use casserole dishes with a diameter under 12 cm. If the flame is accidentally extinguished, switch off the burner and wait for at least 1 minute before attempting to relight it. If the appliance is equipped with a flame failure safety device*(X), press and hold the BURNER knob for approximately 3-7 seconds to keep the flame alight and to activate the device. [. . . ] € The inside of the oven should ideally be cleaned after each use, while it is still lukewarm. Use hot water and detergent, then rinse well and dry with a soft cloth. € Clean the glass part of the oven door using a sponge and a non-abrasive cleaning product, then dry thoroughly with a soft cloth. Do not use rough abrasive material or sharp metal scrapers as these could scratch the surface and cause the glass to crack. [. . . ]