User manual HOTPOINT C 247 G

[. . . ] 11 Important safety warnings To maintain the EFFICIENCY and SAFETY of this appliance, we recommend: • call only the Service Centers authorized by the manufacturer • always use original Spare Parts 1 This appliance is intended for nonprofessional use within the home. 2 These instructions are only for those countries whose symbols appear in the booklet and on the serial no. 3 This owner’s manual is for a class 1 appliance (insulated) or class 2, subclass 1 appliances (installed between two cabinets. 4 Before using your appliance, read the instructions in this owner’s manual carefully since it provides all the information you need to ensure safe installation, use and maintenance. [. . . ] Adapting the cooker to different types of gas In order to adapt the cooker to a different type of gas with respect to the gas for which it was produced (indicated on the label attached to the lid), follow these steps: a) replace the hose holder mounted on the appliance with that supplied in the bag of “cooker accessories”. Important: the hose holder for liquid gas is marked 8, the hose holder for methane gas is marked 13. B) Replacing the burner nozzles on the hob: • remove the grids and slide the burners from their housings; • unscrew the nozzles using a 7 mm socket spanner, and replace them with nozzles for the new type of gas (see table 1 “Burner and nozzle characteristics”). € replace all the components by repeating the steps in reverse order. Connecting the gas The appliance should be connected to the mains or to a gas cylinder in compliance with current directives. Before making the connection, check that the cooker is regulated for the gas supply you are using. If not, follow the instructions indicated in the paragraph “Adapting to different types of gas”. On some models the gas supply can be connected on the left or on the right, as necessary; to change the connection, reverse the position of the hose holder with that of the cap and replace replace the gasket (supplied with the appliance). When using liquid gas from a cylinder, install a pressure regulator which complies with current directive. Important: check that the supply pressure complies with the values indicated in table 1 “Characteristics of the burners and nozzles” since this will ensure safe operation, correct consumption and ensure a longer life to your appliance. Connection with hose Make the connection using a gas hose complying with the the characteristics provided in current directive. The internal diameter of the pipe used is as follows: - 8mm for liquid gas; - 13mm for methane gas. V b) Minimum regulation of the gas oven burner with thermostat (see fig. ): • light the burner as described in the paragraph “the oven knob” of the instruction booklet. € turn the knob to Max for about 10 minutes and then turn the knob to the Min setting; • remove the knob; • regulate the screw positioned outside the thermostat pin until the flame is small but steady. : in the case of liquid gas, the regulation screw must be screwed in to the bottom. Pay particular attention to the plug wires and thermocouple tubes. D Important On completion of the operation, replace the old rating sticker with one indicating the new type of gas used. This sticker is available from our Service Centres. Note Should the pressure of the gas used be different (or vary) from the recommended pressure, it is necessary to fit a suitable pressure regulator onto the inlet pipe in compliance with current National Regulations relative to “regulators for channelled gas”. This appliance conforms with the following European Economic Community directives: 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications; 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications; 90/396/EEC of 29/06/90 (Gas) and subsequent modifications; 93/68/EEC of 22/07/93 and subsequent modifications. Tray for Catching Overflows Gas Burner Electronic Lighting Device (only on a few models) Top Grate Control Panel Adjustable Feet or Legs Dripping Pan or Baking Sheet Flame Failure Device for Cooktop Burners (only on a few models) K. [. . . ] In general, the larger the roast, the lower the temperature setting and the longer the total cooking time. Place the meat on the centre of the rack and place the dripping pan beneath it to catch the fat. Make sure that the rack is inserted so that it is in the centre of the oven. If you would like to increase the amount of heat from below, use the lower rack heights. [. . . ]