User manual HOTPOINT GPL 64L CI RFH

[. . . ] Operating Instructions HOB Contents Installation, 2-5 GB English, 1 GB RS Русский, 12 Positioning Electrical connection Gas connection Data plate Burner and nozzle specifications Description of the appliance, 6 Overall view Start-up and use, 7-8 Practical advice on using the burners Precautions and tips, 9 General safety Disposal GPK 64L GH RU/HA Maintenance and care, 10 Switching the appliance off Cleaning the appliance Gas tap maintenance Troubleshooting, 11 1 Installation !Before operating your new appliance please read this instruction booklet carefully. It contains important information for safe use, installation and care of the appliance. Please keep these operating instructions for future reference. [. . . ] Inner DRDA (DCDR) burner adjustment • Adjusting the burners’ primary air : Does not require adjusting. • Setting the burners to minimum: 1. Remove the knob and adjust the adjustment screw, which is positioned in or next to the tap pin, until the flame is small but steady. In the event of single-control DRDA (DCDR) burners, adjustment can be performed by intervening on the 2 screws located near the tap pin (see picture). total DRDA (DCDR) burner adjustment 3. Having adjusted the flame to the required low setting, while the burner is alight, quickly change the position of the knob from minimum to maximum and vice versa several times, checking that the flame does not go out. Some appliances have a safety device (thermocouple) fitted. If the device fails to work when the burners are set to the low flame setting, increase this low flame setting using the adjusting screw. Once the adjustment has been made, replace the seals on the by-passes using sealing wax or a similar substance. In the event of discrete-adjustment knobs with LED visualisation, turn the knob to the minimum power setting them remove it and intervene on the adjustment screw located near the tap pin. Minimum setting adjustment of the DRDA (DCDR) burner with discrete adjustment and LED visualisation: • To adjust the outer ring, turn the knob anticlockwise to the minimum power position. € To adjust the minimum power setting of the inner ring, turn the knob clockwise to the minimum power position. € Remove the knob and intervene on the adjustment screw located near the tap pin. If the appliance is connected to liquid gas, the regulation screw must be fastened as tightly as possible. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Stickers are available from any of our Service Centres. Should the gas pressure used be different (or vary slightly) from the recommended pressure, a suitable pressure regulator must be fitted to the inlet pipe (in order to comply with current national regulations). 00 0, 90 By-pass 1/100 Nozzle 1/100 Nozzle 1/100 Flow* (l/h) (mm) Reduced Fast (RR) Semi Fast (S) Auxiliary (A) Double flame (DCDR internal) (1) Double flame (1) (DCDR internal) 130 (DCDR external 2 nozzle) (mm) 39 28 28 27 (mm) 80 64 50 44 *** 189 120 73 65 ** 186 118 71 64 (mm) 122 (H) 96 (Y) 79 (6) 74 100 75 55 30 248 157 95 86 27 1, 50 3, 60 55 44 262 60x2 257 3, 60 74 343 100x 2 Supply pressures Nominal (mbar) Minimum (mbar) Maximum (mbar) 28-30 20 35 37 25 45 20 17 25 (1) For single-control DRDA (DCDR) burner only * At 15°C and 1013 mbar - dry gas ** Propane P. 78 MJ/m³ A RR S DC DATA PLATE Electrical see data plate connections This appliance conforms to the following European Economic Community directives: - 2006/95/EEC dated 12/12/06 (Low Voltage) and subsequent amendments - 2004/108/EEC dated 15/12/04 (Electromagnetic Compatibility) and subsequent amendments - 93/68/EEC dated 22/07/93 and subsequent amendments. GPK 64L GH RU/HA 5 Description of the appliance GB Overall view GAS BURNERS Support Grid for COOKWARE Control Knobs for GAS BURNERS SAFETY DEVICES * Ignition for GAS BURNERS * • GAS BURNERS differ in size and power. The system guarantees accurate flame adjustment and uniform cooking results by facilitating selection of the desired power level. The "double-flame" burner This gas burner consists of two concentric flame rings that can operate jointly or independently (in case of dual-control only). [. . . ] After cleaning, rinse and dry any remaining drops of water. It is not necessary to remove the pan supports in order to clean the hob surface. Thanks to the support system, simply lift and hold the pan supports or rotate them until they rest against a rear support. Do not place the hot grids on top of the glass cover (if applicable), otherwise the rubber plugs on the glass may be damaged. [. . . ]