User manual HOTPOINT HB 86 C.2 IX

[. . . ] Operating Instructions OVEN Contents GB English, 1 GB PL Polski, 13 Installation, 2-4 Positioning Electrical connections Data plate Assistance Description of the appliance, 5 Overall view Control panel Start-up and use, 6 Starting the oven Cooking modes, 7-8 HB 86 C. 2 IX Cooking modes Programming your cooking Practical cooking advice Cooking advice table The electronic cooking programmer, 9 Hob, 10 Type of hob Switching on the glass ceramic hob Practical advice on using the glass ceramic hob Precautions and tips, 11 General safety Disposal Respecting and conserving the environment Maintenance and care, 12 Switching the appliance off Cleaning the appliance Cleaning the oven door Replacing the light bulb Installation GB  Before placing your new appliance into operation please read these operating instructions carefully. They contain important information for safe use, for installation and for care of the appliance.  Please keep these operating instructions for future reference. [. . . ] The best results are obtained if you use one cooking rack only. B MULTI-COOKING mode All the heating elements (top, bottom and circular), as well as the fan, will come on. Since the heat remains constant throughout the oven, the air cooks and browns food uniformly. A maximum of two racks may be used at the same time. W PIZZA mode The bottom and circular heating elements, as well as the fan, will come on. This combination heats the oven rapidly by producing a considerable amount of heat, particularly from the bottom element. If you use more than one rack simultaneously, switch the position of the dishes halfway through the cooking process. 7 GB Cooking advice table Setting made Type of food Weight (in kg) 1 1 1 1 0. 5 Position of the rack from the oven bottom 3 3 3 3 3 3 2/3 3 3 2-4 2-4 2-4 1-3-5 1-3-5 1-3-5 2 2 2 2 2 2 2 2 2 2 2 2-4 3 2 2-4 2 2 2-4 2-4 2 2-4 3 3 2 2/3 4 4 4 3/4 4 4 4 4 4 3 3 Preheating time (min. Once cooking is completed, the timer will ring; to turn it off, simply press any button except the ) and * buttons. Immediate start for a specified period By programming just the duration (points 1 and 2 of the “Delayed cooking time for specified period” section), cooking will begin immediately. To cancel a cooking schedule already programmed Press the $ button, and use the ) button to set the time to: GB Button Functions: H : Timer with hours and minutes; $ : cooking time; % : end cooking time; ( : Manual change; ) : set cooking time (to count down); * : set cooking time (to start from zero) How to reset the digital clock After the appliance has been connected to the power supply, or after a power cut, the clock display will automatically reset to 0:00 and begin to blink. • Press the $ and % buttons consecutively and then reset the time (within 4 seconds) using the ) and * buttons. The time can also be changed in the following two ways: 1. Press the ( button, and then use the ) and * buttons to reset the time. Manual operation of the oven Once the time has been set, the programmer automatically switches to manual mode. Note: Press the ( button to restore the manual mode after every “Automatic” cooking session. Delayed cooking time for a specified period The total cooking time as well as the time at which the cooking will finish must be set. if we assume that the time display reads10:00: 1. Turn the oven control knob to the setting and temperature desired (example: static oven mode at 200°C). Press the button $ and then set the cooking time (within four seconds) using the ) and * buttons. Supposing the cooking time is set to 30 minutes, the display will read as follows: then press the manual cooking mode button (. [. . . ] • Always keep the oven door closed when using the GRILL mode to attain best results and to save energy (approximately 10%). • Regularly check the door seals and wipe clean to ensure they are free of debris so that they stick properly to the door and do not allow heat to disperse. 11 Maintenance and care GB Switching the appliance off Disconnect your appliance from the electricity supply before carrying out any work on it. F Cleaning the appliance • The stainless-steel or enamel-coated external parts as well as the rubber seals may be cleaned using a sponge that has been soaked in lukewarm water and neutral soap. [. . . ]