User manual HOTPOINT HGF 6.8 AD X/HA

[. . . ] If you sell, transfer or move the unit to another location, make sure to keep the manual with the product. Read the instructions carefully - they contain important installation, user and safety information. Do not tamper with the electrical or mechanical equipment of the product or its exhaust ducts. € Si consiglia di pulire frequentemente il prodotto, sia internamente che General safety information esternamente (ALMENO UNA VOLTA • The distance between the cookware support surface on top of the cooking AL MESE, rispettare comunque quanto appliance and the lowest part of the espressamente indicato nelle istruzioni cooker hood must be at least: di manutenzione riportate in questo 65 cm if the hood is installed over a gas manuale). [. . . ] The duct must have as smooth an inner surface as possible. The duct must be made of regulatory material. Do not connect the hood to flues carrying combustion fumes from other equipment (boilers, GLASSs, stoves, etc. Observe the instructions of the competent authorities in relation to the air exhaust. The air being exhausted may not be exhausted into a wall cavity unless the cavity in question is specifically intended for this purpose. Equip the room with air intakes to prevent the hood creating suction pressure in the interior (this must not exceed 0. The manufacturer is not liable for any consequences of failure to observe these instructions. Of exhaust tube (cm) 15/12 15/12 Bulb draw (W) Total draw (W) 2 x 40 185 Model code HGF 9. 8 AD X/HA Bulb (V) Bulb draw (W) Total draw (W) Halogen 2 x 40 290 Model code HGA 9. 5 AM X/HA Bulb (V) Bulb draw (W) Total draw (W) Halogen 2 x 40 150 Filter or ducted?If you wish to use it as a filter unit, you must install the proper ACCESSORY KIT. Note: If supplied with the hood, the accessory active charcoal filter unit may already be installed. Instructions for transforming the hood from the ducted to the filter version are given in this manual (see “Filter version”). Halogen 20 W LED * Risk Group 1 according to Standard EN 62471 The hoods are conforming to the following EC Directives: • “Low voltage” Directive 2006/95/EC (12-12-2006) • “EMC” Directive 2004/108/EC (15-12-2004) * Only available in certain models 35 GB GLASS controls Models with mechanical keypad HGA 9. 5 AM X/HA Grease/odour filter warnings The T2 icon flashes to indicate that the grease filter is saturated, while T3 flashes to indicate that the odour filter is saturated, and if both are flashing then both filters are saturated. You must then clean/replace the grease filter (A) or odour filter (B) or both, accordingly (see “Maintenance and care”). To reset the filter counter: Hold down T4 for three seconds while the hood is on. The warning led flashes three times, then returns to its normal mode If both filter warnings are active at the same time, you must reset each separately. The first sequence resets the grease filter, while the second sequence resets the odour filter. Hood configuration: To set the operating mode of the hood, hold down T5 for 6 seconds while the product is off. Icons T2 or T3 will light up to show the type of installation: T2 ventilation, T3 filtering. You can change the type of installation by pressing T4 cyclically. [. . . ] Servicing the grease filter (A) The grease filter retains the particles of grease produced during cooking; it must be cleaned at least once a month with a non-aggressive detergent, either by hand or with a low temperature, short A dishwasher cycle. To extract the grease filter, pull the spring loaded handle. If washed in a dishwasher, the metal filter may change colour, but this does not affect its performance. servicing the charcoal filter (B) The charcoal filter retains unpleasant cooking odours. [. . . ]