User manual HOTPOINT HLB 6.7 AT

[. . . ] If you sell, transfer or move the unit to another location, make sure to keep the manual with the product. Read the instructions carefully - they contain important installation, user and safety information. Do not tamper with the electrical or mechanical equipment of the product or its exhaust ducts. € Si consiglia di pulire frequentemente il prodotto, sia internamente che General safety information esternamente (ALMENO UNA VOLTA • The distance between the cookware support surface on top of the cooking AL MESE, rispettare comunque quanto appliance and the lowest part of the espressamente indicato nelle istruzioni cooker hood must be at least: di manutenzione riportate in questo 65 cm if the hood is installed over a gas manuale). [. . . ] T3 Speed 2 When the button is pressed the hood switches from the previous status to speed 2. T4 Speed 3 When the button is pressed the hood switches from the previous status to speed 3. T5 Booster When the button is pressed the hood switches from the previous status to intense speed. The setting is limited by time; when the time elapses the hood goes back to the speed set previously; when a speed button is pressed (T2, T3 or T4), the selected speed is set as you leave the booster mode. T6 Timer By pressing T6 once, a timer setting can be associated to each speed V) [v1 – 30 min, v2 – 20 min, v3 – 10 min] , after which the hood turns OFF automatically. The timer can be set for manual speeds only and not for the booster. T7 Antigrease and odour filter signal The antigrease (A) and odour (B) filters need cleaning/ replacing after a certain number of hours of use (the latter for filtering hoods only). The time for cleaning/replacement is signalled by the flashing of the coloured LED associated to the filter (white for antigrease filters, red for odour filter). The LED is turned off by pressing the T7 button after cleaning/replacing the filters. T8 lights ON/OFF It turns the work lights of the hood on and off. Hood configuration The configuration menu is accessed with the product off by pressing T5 and T6 for 6 seconds. T7 turns on at this point to indicate the type of installation through two colours of the LED: white for extractor installation (default), red for filtering installation. The installation type can be changed by pressing T7 cyclically with the consequent alternation of the LED colours. 31 Models with Touch control glass + display GB (high) HLB 9. 8ASH (CF) X/HA T8 lights ON/OFF It turns the work lights of the hood on and off. I1 D1 D2 I5 T1 T2 T3 T4 T5 T6 T7 T8 I2 D1: DGT Speed D2: Assembly of 2 DGT Time I1: Grease Filter Indicator I2: Carbon Filter Indicator I4: Menu Indicator I5: Timer Indicator I4 T1 motor ON/OFF When the button is pressed with the hood off, the first speed is set. When the button is pressed during operation, the hood switches OFF. T2 Speed – When the button is pressed the hood switches to the previous speed. T3 Speed + When the button is pressed the hood switches to the next speed. If the hood is off, speed 1 is set when pressing this button. T4 Booster When the button is pressed, the hood switches from the previous status to the intensive speed; the letter “b” will flash slowly on the display. The setting has a limited timeframe; when the time elapses the hood goes back to the speed set previously; when a speed button is pressed (T2, T3 or T4), the selected speed is set as you leave the booster mode. [. . . ] This filter can NOT be washed or regenerated Disassembly: Remove the activated-carbon filter by B pressing the two front levers which secure it to the hood. Assembly: Insert the filter inside the box paying attention to its orientation (the hollow part of the filer must face the hood). Secure the filter with the fastening screw provided. Assembly: Secure the activated-carbon filter first in the back using the hood's metal tabs and then in the front by pressing the two levers. [. . . ]