User manual HOTPOINT KT 8104 QO

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HOTPOINT KT 8104 QO. We hope that this HOTPOINT KT 8104 QO user guide will be useful to you.

Lastmanuals help download the user guide HOTPOINT KT 8104 QO.


Mode d'emploi HOTPOINT KT 8104 QO
Download
Manual abstract: user guide HOTPOINT KT 8104 QO

Detailed instructions for use are in the User's Guide.

[. . . ] 2 Before using the appliance, carefully read the instructions contained in this manual, as they provide important information for ensuring safe installation, use and maintenance. 3 After the packing has been removed, make sure the appliance has not been damaged during transport. If you have any doubts, do not use the appliance. Call a qualified technician for assistance. [. . . ] REAR SPRING ASSEMBLY REAR LEFT MOUNTING REAR RIGHT MOUNTING 30 WORK SURFACE 40 FRONT OF THE HOB UNIT HOB UNIT FACE DOWN FRONT LEFT MOUNTING FRONT RIGHT MOUNTING SEAL MOUNTING FRONT / REAR RIGHT / LEFT MOUSSE 5x8 mm 48 10 51 0 Leave this much space between the bottom and the cabinetry 56 0+ /- 1 49 0+ /- 1 X (CEI 335-2-6) The aforementioned measurements must absolutely be observed in so far as improper installation can cause the surrounding surface areas to overheat. It is recommended that the cooktop be installed at a distance of at least 40 mm from the back wall or other vertical surfaces to ensure that the air circulates properly over the cooking area and to avoid overheating the surrounding surfaces. A seal or gasket is provided with the cooktop; make sure that it adheres properly to the bottom part of the frame of the cooktop. It is indispensable that the seal fits properly around the entire cooktop frame and especially along the corners in order to create a seal between the counter top and the cooktop itself so as to prevent spills or splashes from leaking into the cabinet below. Very important It is essential to instali the hob on a totally flat surtace. Any damage caused by incorrect fitting may alter the characteristics or impair performance. Insert the cooktop into the hole, pressing firmly around the frame to make it adhere to the counter top. C) If a wooden panel is installed beneath the cooktop for insulation purposes, it must be positioned at least 20 mm from the bottom part of the cooktop itself. Note: If the cooktop is installed above a built-in oven, it is preferable that the oven be installed in such a way that it is set on two strips of wood; if, on the other hand, the oven is installed on a continuous base, there must be an opening in the back of at least 45 x 560 mm. The built-in oven must be equipped with a forced air cooling system. Make certain that the seal around the outside edge of the hob is correctly installed in order to avoid any leakage into the cabinetry below. 9 Technical specifications Electrical connection · Detail of wiring - Connect the 5 wires to your machine respecting the colour of the wires and their connections. Black Blue Brown Black Green / Yellow The electrical safety ot this appliance is guaranteed only if the appliance is correctly earthed in compliance with the standards of electrical safety. The manufacturer can under no circumstances be considered responsible for any damage that might occur due to incorrect earthing of the appliance. neutral Live 1 · Important points Your hob unit is supplied with a special Scholtès connection cable. If ever the cable is damaged, it should be replaced by an authorised service engineer only. Disconnect the appliance before any work is carried out. live 2 N L1 L2 Two-phase wiring Earth Black Blue Black Green / Yellow · € • • Fasten the appropriate standard plug for the load indicated the rating plate to the chord. If the appliance must be directly connected to the mains, a multipolar switch must be installed between the appliance and the mains. The multipolar switch must have a minimum of 3 mm of space between the contacts, be sized to the load, and comply with current regulations (the switch must not be able to disconnect the earth conductor). The supply cord must be positioned so that no part of it reaches a temperature of 50 °C higher than room temperature. Before making the connection, make sure that: the limiter valve and the residential wiring can support the appliance load (see rating plate); the mains system is properly earthed in compliance with current regulations and provisions; there is easy access to the socket or the multipolar switch after the appliance is installed. [. . . ] Do not get too close to the cooking areas when they are hot. The ceramic glass used to make the cooktop is very durable. However, should it crack, do not use the cooktop and disconnect it from the power supply. Instructions for using the appliance the first time: The glue used for the seals may leave grease residues on the glass during storage. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HOTPOINT KT 8104 QO

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HOTPOINT KT 8104 QO will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag