User manual HOTPOINT LL 42 EU.C/HA

[. . . ] 12 Instruction booklet DISHWASHER Contents Installation, Positioning and levelling Connecting the water and electricity supplies Technical data EN English, 13 14-15 Description of the appliance, 16 Overall view Control panel Loading the racks, 17 Lower rack Cutlery basket Upper rack Start-up and use, LL 42 Starting the dishwasher Loading the detergent Washing options 18 Wash cycles, 19 Wash cycle table Rinse aid and refined salt, Loading the rinse aid Loading the refined salt 20 Care and maintenance, 21 Shutting off the water and electricity supplies Cleaning the dishwasher Preventing unpleasant odours Cleaning the sprayer arms Cleaning the filters Leaving the machine unused for extended periods Precautions and advice, 22 General safety Disposal Saving energy and respecting the environment Troubleshooting, Assistance, 24 23 Before calling for Assistance Installation EN Keep this instruction manual in a safe place for future reference. If the appliance is sold, given away or moved, please ensure the manual is kept with the machine, so that the new owner may benefit from the advice contained within it. Please read this instruction manual carefully: it contains important information regarding the safe installation, use and maintenance of the appliance. If the appliance must be moved at any time, keep it in an upright position; if absolutely necessary, it may be tilted onto its back. [. . . ] Illuminated light: add rinse aid; unlit light: there is no shortage of rinse aid in the dispenser. • when the LOW RINSE AID* indicator light on the panel flashes; 1. Open the dispenser by turning the lid (G) in an anticlockwise H direction. Pour in the rinse aid, making sure it does not overflow from the dispenser. If this happens, clean F the spill immediately with a dry cloth. NEVER pour the rinse aid directly into the appliance tub. Remove the lower rack and unscrew the cap of the dispenser (in an anticlockwise direction). For the first wash cycle only: fill the dispenser up to the edges with water. Position the funnel* provided correctly (see figure) and fill the salt dispenser up to the edges (approximately 2 kg); it is normal for a little water to leak out. Remove the funnel*, wipe away any salt residue from the thread and screw the cap on tightly, so that detergent does not leak into the dispenser during the wash cycle (this could damage the water softening system beyond repair). When necessary, measure out the salt before a wash cycle so that any saline solution which has leaked out of the salt dispenser is removed. Adjusting the amount of salt* It is possible to adjust the amount of salt used according to the hardness of the water in your area (this information is available from your local water board). Turn the arrow on the neck of the dispenser (see figure) towards the + or symbols, using the table below as a guide. Hardness of the water Selector knob position / MED + Salt Autonomy consumption (cycles/2 kg) (grams/cycle) 0 20 40 60 / 60 40 25 Adjusting the amount of rinse aid If you are not completely satisfied with the washing or drying results, you may adjust the quantity of rinse aid used. Use a screwdriver to turn the dosage adjuster to one of the 6 pre-set positions (the default position is set to 4): • if there are white streaks on the crockery, set the adjuster to a lower number (1-3). • if drops of water remain on the crockery or there are limescale marks present after the cycle has finished, set the adjuster to a higher number (4-6). If you are using multi-functional tablets and you wish to further improve the drying performance of the appliance, fill the dispenser and set the dosage adjuster to 2. - If using multi-functional tablets fill the salt dispenser and set the adjuster to -; if the hardness of the water is greater than 60°fH, set it to +. Loading the refined salt In order to obtain the best possible results from a wash cycle, make sure that the dispenser is never empty. Refined salt removes limescale from the water, thus avoiding the formation of deposits on crockery. The salt dispenser is located in the lower part of the dishwasher (see Description) and should be filled: * Only available in selected models. 20 Care and maintenance Shutting off the water and electricity supplies • Turn off the water tap after every wash cycle to avoid leaks. [. . . ] The crockery has not be en d r i e d p r o p e r l y. • • • • • • • • • • • • The dishes are n ot clea n. The dishw asher does not take an y w ater in /Tap sh utoff alarm . (several short beeps are emitted)* Only available in selected models. [. . . ]